- 您現在的位置：買賣IC網 > PDF目錄16896 > MAX4104EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX4104 PDF資料下載
參數資料
| 型號： | MAX4104EVKIT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/12頁 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX4104 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 每 IC 通道數： | 1 - 單 |
| 放大器類型： | 電壓反饋 |
| 輸出類型： | 單端 |
| 轉換速率： | 400 V/µs |
| -3db帶寬： | 625MHz |
| 電流 - 輸出 / 通道： | 70mA |
| 工作溫度： | -40°C ~ 85°C |
| 電流供應（主 IC）： | 20mA |
| 電壓 - 電源，單路/雙路(±)： | ±3.5 V ~ 5.5 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX4104，MAX4105，MAX4304，MAX4305 |
_______________Detailed Description
The MAX4104/MAX4105/MAX4304/MAX4305 are ultra-
high-speed, low-noise amplifiers featuring -3dB band-
widths up to 880MHz, 0.1dB gain flatness up to
100MHz, and low differential gain and phase errors of
0.01% and 0.01°, respectively. These devices operate
on dual power supplies ranging from ±3.5V to ±5.5V
and require only 20mA of supply current.
The MAX4104/MAX4304/MAX4105/MAX4305 are opti-
mized for minimum closed-loop gains of +1V/V, +2V/V,
+5V/V and +10V/V (respectively) with corresponding
-3dB bandwidths of 880MHz, 730MHz, 430MHz, and
350MHz. Each device in this family features a low input
voltage noise density of only 2.1nV/
√Hz (at 1MHz), an
output current drive of ±70mA, and spurious-free
dynamic range as low as -88dBc (5MHz, RL = 100).
___________Applications Information
Layout and Power-Supply Bypassing
The MAX4104/MAX4105/MAX4304/MAX4305 have an
extremely high bandwidth, and consequently require
careful board layout, including the possible use of
constant-impedance microstrip or stripline techniques.
To realize the full AC performance of these high-speed
amplifiers, pay careful attention to power-supply
bypassing and board layout. The PC board should
have at least two layers: a signal and power layer on
one side, and a large, low-impedance ground plane on
the other side. The ground plane should be as free of
voids as possible. With multilayer boards, locate the
ground plane on a layer that incorporates no signal or
power traces.
Regardless of whether or not a constant-impedance
board is used, it is best to observe the following guide-
lines when designing the board:
1) Do not use wire-wrapped boards (they are much too
inductive) or breadboards (they are much too
capacitive).
2) Do not use IC sockets. IC sockets increase reac-
tances.
3) Keep signal lines as short and straight as possible.
Do not make 90° turns; round all corners.
4) Observe high-frequency bypassing techniques to
maintain the amplifier’s accuracy and stability.
5) Bear in mind that, in general, surface-mount compo-
nents have shorter bodies and lower parasitic reac-
tance, resulting in greatly improved high-frequency
performance over through-hole components.
The bypass capacitors should include 1nF and 0.1F
ceramic surface-mount capacitors between each sup-
ply pin and the ground plane, located as close to the
package as possible. Optionally, place a 10F tantalum
capacitor at the power supply pins’ point of entry to the
PC board to ensure the integrity of incoming supplies.
The power-supply trace should lead directly from the
tantalum capacitor to the VCC and VEE pins. To mini-
mize parasitic inductance, keep PC traces short and
use surface-mount components.
Input termination resistors and output back-termination
resistors, if used, should be surface-mount types, and
should be placed as close to the IC pins as possible.
DC and Noise Errors
The MAX4104/MAX4105/MAX4304/MAX4305 output
offset voltage, VOUT (Figure 1), can be calculated with
the following equation:
VOUT = [VOS + (IB+ x RS) + (IB- x (RF
|| RG))] [1 + RF / RG]
where:
VOS = input offset voltage (in volts)
1 + RF/RG = amplifier closed-loop gain (dimensionless)
IB+ = noninverting input bias current (in amps)
IB- = inverting input bias current (in amps)
RG = gain-setting resistor (in ohms)
RF = feedback resistor (in ohms)
RS = source resistor at noninverting input (in ohms)
The following equation represents output noise density:
e
1
R
i x R
R
e
n(OUT)
F
G
n
S
2
n
F
G
2
n
2
||
=
+
(
) + (
)
+
MAX4104/MAX4105/MAX4304/MAX4305
740MHz, Low-Noise, Low-Distortion
Op Amps in SOT23-5
_______________________________________________________________________________________
9
_____________________Pin Description
SOT23-5
SO
OUT
VCC
VEE
IN+
IN-
N.C.
NAME
Amplifier Output
6
1
Positive Power Supply
7
5
Negative Power Supply
4
2
Amplifier Noninverting
Input
3
Amplifier Inverting Input
2
4
Not internally connected.
1, 5, 8
—
FUNCTION
PIN
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4Z-EY | CONVERTER MOD DC/DC 2V 20W |
| REC5-4805SRWZ/H4/C | CONV DC/DC 5W 18-72VIN 05VOUT |
| MAX9622EVKIT+ | KIT EVALUATION FOR MAX9622 |
| LM4040AEM3-3.0+T | IC VREF SHUNT PREC 3V SOT-23-3 |
| GMC07DREI-S93 | CONN EDGECARD 14POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4105 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:740MHz, Low-Noise, Low-Distortion Op Amps in SOT23-5 |
| MAX4105ESA | 功能描述:運算放大器 - 運放 740MHz Low-Noise Low-Distortion RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4105ESA+ | 功能描述:運算放大器 - 運放 740MHz Low-Noise Low-Distortion RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4105ESA+T | 功能描述:運算放大器 - 運放 740MHz Low-Noise Low-Distortion RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4105ESA-T | 功能描述:運算放大器 - 運放 740MHz Low-Noise Low-Distortion RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。