- 您現在的位置：買賣IC網 > PDF目錄3519 > MAX4081TAUA+ (Maxim Integrated Products)IC AMP CURRENT SENSE 8-UMAX PDF資料下載
參數資料
| 型號： | MAX4081TAUA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURRENT SENSE 8-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 放大器類型： | 電流檢測 |
| 電路數： | 1 |
| 增益帶寬積： | 150kHz |
| 電流 - 輸入偏壓： | 5µA |
| 電壓 - 輸入偏移： | 100µV |
| 電流 - 電源： | 103µA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 76 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 產品目錄頁面： | 1387 (CN2011-ZH PDF) |
The full-scale output voltage is VOUT = RSENSE ILOAD
(MAX) AV, for the MAX4080 and VOUT = VREF ±
RSENSE ILOAD(MAX) AV for the MAX4081.
VSENSE(MAX) is 1000mV for the 5V/V gain version,
250mV for the 20V/V gain version, and 100mV for the
60V/V gain version.
Choosing the Sense Resistor
Choose RSENSE based on the following criteria:
Voltage Loss: A high RSENSE value causes the
power-source voltage to degrade through IR loss. For
minimal voltage loss, use the lowest RSENSE value.
Accuracy: A high RSENSE value allows lower cur-
rents to be measured more accurately. This is due to
offsets becoming less significant when the sense
voltage is larger. For best performance, select
RSENSE to provide approximately 1000mV (gain of
5V/V), 250mV (gain of 20V/V), or 100mV (gain of
60V/V) of sense voltage for the full-scale current in
each application.
Efficiency and Power Dissipation: At high current
levels, the I2R losses in RSENSE can be significant.
Take this into consideration when choosing the
resistor value and its power dissipation (wattage)
rating. Also, the sense resistor’s value might drift if it
is allowed to heat up excessively.
Inductance: Keep inductance low if ISENSE has a
large high-frequency component. Wire-wound resis-
tors have the highest inductance, while metal film is
somewhat better. Low-inductance, metal-film resis-
tors are also available. Instead of being spiral-
wrapped around a core, as in metal-film or wire-
wound resistors, they are a straight band of metal
and are available in values under 1
.
Because of the high currents that flow through RSENSE,
take care to eliminate parasitic trace resistance from
causing errors in the sense voltage. Either use a four-
terminal current-sense resistor or use Kelvin (force and
sense) PC board layout techniques.
Dynamic Range Consideration
Although the MAX4081 have fully symmetrical bidirec-
tional VSENSE input capability, the output voltage range
is usually higher from REF to VCC and lower from REF
to GND (unless the supply voltage is at the lowest end
of the operating range). Therefore, the user must con-
sider the dynamic range of current monitored in both
directions and choose the supply voltage and the refer-
ence voltage (REF) to make sure the output swing
above and below REF is adequate to handle the swings
without clipping or running out of headroom.
Power-Supply Bypassing and Grounding
For most applications, bypass VCC to GND with a 0.1F
ceramic capacitor. In many applications, VCC can be
connected to one of the current monitor terminals (RS+
or RS-). Because VCC is independent of the monitored
voltage, VCC can be connected to a separate regulated
supply.
If VCC will be subject to fast-line transients, a series
resistor can be added to the power-supply line of the
MAX4080/MAX4081 to minimize output disturbance.
This resistance and the decoupling capacitor reduce
the rise time of the transient. For most applications, 1k
in conjunction with a 0.1F bypass capacitor work well.
The MAX4080/MAX4081 require no special considera-
tions with respect to layout or grounding. Consideration
should be given to minimizing errors due to the large
charge and discharge currents in the system.
76V, High-Side, Current-Sense Amplifiers with
Voltage Output
MAX4081
RSENSE
ILOAD = 0
LOAD
VCC
GND
RS-
RS+
OUT
REF1A
REF1B
5V
10V
MAX4081
RSENSE
ILOAD = 0
LOAD
VCC
GND
RS-
RS+
OUT
REF1A
REF1B
5V
Figure 4. MAX4081 Reference Inputs
MAX4080/MAX4081
12
Maxim Integrated
相關PDF資料 |
PDF描述 |
|---|---|
| 929710-03-18-RK | CONN HEADER .100 DUAL STR 36POS |
| 929836-05-26 | CONN HEADER .100 DUAL STR 52POS |
| MMS-130-01-L-SH | CONN RCPT 2MM 30POS SGL HORZ PCB |
| MAX4081SASA+ | IC AMP CURRENT SENSE 8-SOIC |
| 6-103542-2 | 26 MODII HDR DRST UNSHRD A/PIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4081TAUA+ | 功能描述:電流靈敏放大器 76V High-Side Crnt Sense Amp w/V Out RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4081TAUA+T | 功能描述:電流靈敏放大器 76V High-Side Crnt Sense Amp w/V Out RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4081TAUA-T | 功能描述:電流靈敏放大器 76V High-Side Crnt Sense Amp w/V Out RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX40-85CA | 制造商:MDE 制造商全稱:MDE Semiconductor, Inc. 功能描述:HIGH CURRENT TRANSIENT VOLTAGE SUPPRESSOR (TVS) DIODE STAND-OFF VOLTAGE 12 TO 150 Volts 40000 Watt Peak Pulse Power |
| MAX408ACJA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage-Feedback Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。