參數資料
型號： MAX4069AUB+
廠商： Maxim Integrated Products
文件頁數： 2/18頁
文件大?。?/td> 0K
描述： IC AMP CURRENT SENSE 10-UMAX
其它有關文件： Automotive Product Guide
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
放大器類型： 電流檢測
電路數： 1
-3db帶寬： 100kHz
電流 - 輸入偏壓： 2.4µA
電壓 - 輸入偏移： 80µV
電流 - 電源： 100µA
電壓 - 電源，單路/雙路(±)： 2.7 V ~ 24 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-µMAX
包裝： 管件
產品目錄頁面： 1387 (CN2011-ZH PDF)
Detailed Description
The MAX4069–MAX4072 bidirectional, high-side, cur-
rent-sense amplifiers are ideal for portable equipment.
The wide 1.35V to 24V input common-mode voltage
range is independent of the supply voltage, ensuring
that the current-sense feedback remains accurate even
when connected to a battery pack in deep discharge.
The MAX4069/MAX4071/MAX4072 operate from a 2.7V
to 24V single supply. Because the MAX4070 has a 2.5V
internal reference, it operates from 3.6V to 24V. All
devices have a low 100A supply current that reduces
to only 10A (typ) in shutdown mode. To achieve maxi-
mum flexibility, an external current-sense resistor is
used along with a gain select pin (GSEL) to choose
either 50V/V or 100V/V. Drive GSEL low to select gain of
50V/V or drive GSEL high to choose gain of 100V/V
(see
Functional Diagram). The MAX4069 has an
adjustable reference voltage set by two external resis-
tors between REFOUT and ADJ, and GND pins. The
MAX4070 contains an internal 2.5V reference. The
MAX4071 is similar to the MAX4070 but with a fixed
internal reference voltage of 1.5V. The MAX4072 has a
reference input pin to allow use of external references.
Charging current is represented by an output voltage
from the reference voltage to VCC, while discharge cur-
rent is given from the reference voltage to GND. The
direction of VSENSE is totally arbitrary.
The input stage of the MAX4069–MAX4072 is shown in
Figure 1. Its unique topology allows for monitoring bidi-
rectional currents through the sense resistor (RSENSE). If,
for instance, current flows from RS+ to RS-, the
MAX4069–MAX4072 match for the voltage drop over the
external sense resistor (RSENSE) by increasing the cur-
rent through the internal Q1 and RG1. At the same time,
the current through Q2 and RG2 decreases, however,
internal circuitry not shown in Figure 1 prevents Q2 from
turning off completely. Likewise, if current flows from RS-
to RS+, the current through Q2 and RG2 increases and
the current through Q1 decreases. In this way, the volt-
ages at the input terminals of the internal amplifier A1 are
kept constant and an accurate measurement of the sense
voltage is achieved. In the following amplifier stages of
the MAX4069–MAX4072, the output signal of amplifier A2
is level-shifted towards the reference voltage (VREF),
resulting in a voltage at the output pin (OUT) that swings
above the VREF voltage for positive-sense voltages and
below VREF for negative-sense voltages.
Applications Information
Bidirectional, Current-Sense Amplifier
Systems such as laptop computers and other devices
that have internal charge circuitry require a precise bidi-
rectional, current-sense amplifier to accurately monitor
the battery’s current regardless of polarity. Figure 2
shows the MAX4069–MAX4072 used as a bidirectional
current monitor. In Figure 2, the direction of VSENSE is
assigned to charge and discharge, assuming charge is
greater than discharge. The practical choice of direction
is based on dynamic range at OUT, given that the range
of REF to VCC is usually greater than from REF to
ground. This is useful for implementing either smart bat-
tery packs or fuel gauges.
High-Current Measurement
The MAX4069–MAX4072 can achieve high-current
measurements by using low-value sense resistors,
which can be paralleled to further increase the current-
sense limit.
Adjusting VREF (MAX4069)
The MAX4069 has an output reference voltage that can
be set to a desired voltage by a two-resistor divider
between REFOUT, ADJ, and GND. If REFOUT and ADJ
are connected together, the minimum output reference
voltage is obtained, 1.23V (typ). The maximum voltage
for REFOUT is 4V (that requires VCC ≥ 5.1V). The rec-
ommended range for the external resistors is: R1 + R2
should be > 20k and < 500k.
Bidirectional, High-Side, Current-Sense
Amplifiers with Reference
MAX4069–MAX4072
RSENSE
RS-
RS+
RG2
RG1
A1
A2
Q1
Q2
IOUT
OUT
Figure 1. Detailed Input Stage
Note:
RG1 = RG2 = 104k (typ).
MAX4069–MAX4072
10
Maxim Integrated
相關PDF資料
PDF描述
57102-G06-08ULF MINITEK
73084-0 TERMINAL JACK MALE 6-32 BLACK
MAX4491AUA+ IC OP AMP DUAL R-R I/O 8-UMAX
BK/GMA-250-R FUSE 250MA 250V FAST GLS 5X20 UL
102570-8 CONN HEADER R/A .100 20POS 15AU
相關代理商/技術參數
參數描述
MAX4069AUB+ 功能描述:電流靈敏放大器 Bidirectional High Side Crnt-Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
MAX4069AUB+T 功能描述:電流靈敏放大器 Bidirectional High Side Crnt-Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
MAX4069AUB-T 功能描述:電流靈敏放大器 Bidirectional High Side Crnt-Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
MAX4069-MAX4072 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Bidirectional, High-Side, Current-Sense Amplifiers with Reference
MAX406A 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1.2レA Max, Single/Dual/Quad, Single-Supply Op Amps
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*