- 您現在的位置：買賣IC網 > PDF目錄11810 > MAX3109ETJ+T (Maxim Integrated Products)IC UART PDF資料下載
參數資料
| 型號： | MAX3109ETJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 39/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART |
| 產品培訓模塊： | Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Dual Serial UART with 128-Word FIFOs
MAX3109
44
Maxim Integrated
Flow Control Register (FlowCtrl)
The FlowCtrl register configures hardware (RTS/CTS) and software (XON/XOFF) flow control as well as special char-
acters detection.
Bits 7–4: SwFlowx
The SwFlowx bits select the XON and XOFF characters used for auto software flow control and/or special character
detection in combination with the characters programmed in the XON1, XON2, XOFF2, and/or XOFF2 registers. See
table 3.
If auto software flow control is enabled (through FlowCtrl[3]:SwFlowEn) and special character detection is not enabled,
SwFlowx allows selecting either single or dual XON/XOFF character flow control. When double character flow control
is enabled, the transmitter sends out XON1/XOFF1 first followed by XON2/XOFF2 during receive flow control. For
transmit flow control, the receiver only recognizes the received character sequence XON1/XOFF1 followed by XON2/
XOFF2 as a valid control sequence to resume/halt transmission.
If only special character detection is enabled (through MODE2[4]: SpecialChr) while auto software flow control is dis-
abled, the SwFlowx allows selecting either single or double character detection. Single character detection allows the
detection of two characters: XON1 or XON2 and XOFF1 or XOFF2. Double character detection does not distinguish
between the sequence of the two received XON1/XON2 or XOFF1/XOFF2 characters. The two characters have to be
received in succession, but it is insignificant which of the two is received first. The special characters are deposited in
the receive FIFO. An ISR[1]: SpCharInt interrupt is generated when special characters are received.
Auto software flow control and special character detection can be enabled to operate simultaneously. If both are
enabled, XON1 and XOFF1 define the auto flow control characters, while XON2 and XOFF2 constitute the special
character detection characters.
Bit 3: SwFlowEn
Set the SwFlowEn bit high to enable auto software flow control. The characters used for automatic software flow control
are selected by SwFlowx. If special character detection is enabled by setting the MODE2[4]: SpecialChr bit high in
addition to automatic software flow control, XON1 and XOFF1 are used for flow control while XON2 and XOFF2 define
the special characters.
Bit 2: GPIAddr
Set the GPIAddr bit high to enable the four GPIO_ inputs to be used in conjunction with XOFF2 for the definition of a
special character. This can be used, for example, for defining the address of an RS-485 slave device through hard-
ware. The GPIO_ input logic levels define the four LSBs of the special character, while the four MSBs are defined by
the XOFF2[7:4] bits. The contents of the XOFF2[3:0] bits are neglected while the GPIO_ inputs are used in special
character definition. Reading the XOFF2 register does not reflect the logic on GPIO_ in this mode.
Bit 1: AutoCTS
Set the AutoCTS bit high to enable AutoCTS flow control mode. In this mode, the transmitter stops and starts sending
data at the TX_ interface depending on the logic state of the CTS_ input. See the Auto Hardware Flow Control sec-
tion for more information about AutoCTS flow control mode. Logic changes at the CTS_ input result in an interrupt in
ISR[7]: CTSInt. The transmitter must be turned off by setting the MODE1[1]: TxDisabl bit high before AutoCTS mode
is enabled.
Bit 0: AutoRTS
Set the AutoRTS bit high to enable AutoRTS flow control mode. In this mode, the logic state of the RTS_ output is
dependent on the receive FIFO fill level. The FIFO thresholds at which RTS_ changes state are set in FlowLvl. See the
Auto Hardware Flow Control section for more information about AutoRTS flow control mode.
ADDRESS:
0x13
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
SwFlow3
SwFlow2
SwFlow1
SwFlow0
SwFlowEn
GPIAddr
AutoCTS
AutoRTS
RESET
0
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484T14A15S | CONN PLUG 15POS STRAIGHT W/SCKT |
| 1812PC224MAT3A | CAP CER 0.22UF 250V 20% X7R 1812 |
| VI-J5L-IW-F2 | CONVERTER MOD DC/DC 28V 100W |
| VI-J5L-IW-F1 | CONVERTER MOD DC/DC 28V 100W |
| MS27468E17F8P | CONN RCPT 8POS JAM NUT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX310C/D | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE+ | 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CWN | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CWN+ | 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。