- 您現在的位置：買賣IC網 > PDF目錄3761 > MAX3082CSA (Maxim Integrated Products)IC TXRX RS485/RS422 10MBPS 8SOIC PDF資料下載
參數資料
| 型號： | MAX3082CSA |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS485/RS422 10MBPS 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
Fail-Safe
The MAX3080 family guarantees a logic-high receiver
output when the receiver inputs are shorted or open, or
when they are connected to a terminated transmission
line with all drivers disabled. This is done by setting the
receiver threshold between -50mV and -200mV. If the
differential receiver input voltage (A-B) is greater than
or equal to -50mV, RO is logic high. If A-B is less than
or equal to -200mV, RO is logic low. In the case of a
terminated bus with all transmitters disabled, the
receiver’s differential input voltage is pulled to 0V by
the termination. With the receiver thresholds of the
MAX3080 family, this results in a logic high with a 50mV
minimum noise margin. Unlike previous fail-safe
devices, the -50mV to -200mV threshold complies with
the ±200mV EIA/TIA-485 standard.
MAX3089 Programming
The MAX3089 has several programmable operating
modes. Transmitter rise and fall times are programma-
ble between 2500ns, 750ns, and 25ns, resulting in
maximum data rates of 115kbps, 500kbps, and
10Mbps, respectively. To select the desired data rate,
drive SRL to one of three possible states by using a
three-state driver, by connecting it to VCC or GND, or
by leaving it unconnected. For 115kbps operation, set
the three-state device in high-impedance mode or
leave SRL unconnected. For 500kbps operation, drive
SRL high or connect it to VCC. For 10Mbps operation,
drive SRL low or connect it to GND. SRL can be
changed during operation without interrupting data
communications.
Occasionally, twisted-pair lines are connected back-
ward from normal orientation. The MAX3089 has two
pins that invert the phase of the driver and the receiver
to correct for this problem. For normal operation, drive
TXP and RXP low, connect them to ground, or leave
them unconnected (internal pulldown). To invert the dri-
ver phase, drive TXP high or connect it to VCC. To
invert the receiver phase, drive RXP high or connect it
to VCC. Note that the receiver threshold is positive
when RXP is high.
The MAX3089 can operate in full- or half-duplex mode.
Drive the H/F pin low, leave it unconnected (internal
pulldown), or connect it to GND for full-duplex opera-
tion, and drive it high for half-duplex operation. In full-
duplex mode, the pin configuration of the driver and
receiver is the same as that of a MAX3080 (Figure 4). In
half-duplex mode, the receiver inputs are switched to
the driver outputs, connecting outputs Y and Z to inputs
A and B, respectively. In half-duplex mode, the internal
full-duplex receiver input resistors are still connected to
pins 11 and 12.
Applications Information
256 Transceivers on the Bus
The standard RS-485 receiver input impedance is 12k
(one-unit load), and the standard driver can drive up to
32 unit loads. The MAX3080 family of transceivers have
a 1/8-unit-load receiver input impedance (96k
), allow-
ing up to 256 transceivers to be connected in parallel
on one communication line. Any combination of these
devices and/or other RS-485 transceivers with a total of
32 unit loads or less can be connected to the line.
Reduced EMI and Reflections
The MAX3080–MAX3085, and MAX3089 with SRL = VCC
or unconnected, are slew-rate limited, minimizing EMI
and reducing reflections caused by improperly termi-
nated cables. Figure 14 shows the driver output wave-
form and its Fourier analysis of a 20kHz signal
transmitted by a MAX3086/MAX3087/MAX3088, and
MAX3089 with SRL = GND. High-frequency harmonic
Fail-Safe, High-Speed (10Mbps),
Slew-Rate-Limited RS-485/RS-422 Transceivers
R
Y
Z
VOD
VOC
Figure 5. Driver DC Test Load
RECEIVER
OUTPUT
TEST POINT
1k
1k
S1
S2
VCC
CRL
15pF
Figure 6. Receiver Enable/Disable Timing Test Load
Maxim Integrated
15
MAX3080–MAX3089
相關PDF資料 |
PDF描述 |
|---|---|
| SY87721LHG | IC CLOCK/DATA RECOVERY 64-TQFP |
| MAX3082CPA | IC TXRX RS485/RS422 10MBPS 8-DIP |
| MAX3221CAE | IC TXRX RS232 120KBPS SD 16-SSOP |
| SY87701LHI | IC CLOCK/DATA RECOVERY 32-TQFP |
| MAX1406CPE | IC TXRX RS232 230KBPS 16-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3082CSA+ | 功能描述:RS-422/RS-485 接口 IC Fail-Safe 10Mbps RS-485/RS-422 Tcvr RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX3082CSA+T | 功能描述:RS-422/RS-485 接口 IC Fail-Safe 10Mbps RS-485/RS-422 Tcvr RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX3082CSA-T | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX3082ECPA | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX3082ECPA+ | 功能描述:RS-422/RS-485 接口 IC Fail-Safe 10Mbps RS-485/RS-422 Tcvr RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。