參數資料
型號: MAX3051ESA+T
廠商: Maxim Integrated Products
文件頁數: 2/12頁
文件大?。?/td> 0K
描述: IC TXRX CAN 1MBPS 8-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: 收發器
驅動器/接收器數: 1/1
規程: CAN
電源電壓: 3.14 V ~ 3.47 V
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOIC
包裝: 帶卷 (TR)
MAX3051
+3.3V, 1Mbps, Low-Supply-Current
CAN Transceiver
10
Maxim Integrated
is switched off and the receiver is switched to a low-
current/low-speed state. If dominant bits are detected,
RXD switches to low level. The microcontroller should
react to this condition by switching the transceiver back
to normal operation.
When the MAX3051 enters standby mode, RXD goes
high for 4s (max) regardless of the BUS state.
However, after 4s, RXD goes low only when the BUS
is dominant, otherwise RXD remains high (when the
BUS is recessive). For proper measurement of standby-
to-receiver active time (tSBRXDL), the BUS should be in
dominant state (see Figure 2).
Shutdown
Drive SHDN high to enter shutdown mode. Connect SHDN
to ground or leave unconnected for normal operation.
Thermal Shutdown
If the junction temperature exceeds +160°C, the device
is switched off. The hysteresis is approximately 25°C,
disabling thermal shutdown once the temperature
drops below 135°C. In thermal shutdown, CANH and
CANL go recessive and all IC functions are disabled.
Applications Information
Reduced EMI and Reflections
In slope-control mode, the CANH and CANL outputs
are slew-rate limited, minimizing EMI and reducing
reflections caused by improperly terminated cables.
In multidrop CAN applications, it is important to main-
tain a direct point-to-point wiring scheme. A single pair
of wires should connect each element of the CAN bus,
and the two ends of the bus should be terminated with
120
resistors (Figure 6). A star configuration should
never be used.
Any deviation from the point-to-point wiring scheme
creates a stub. The high-speed edge of the CAN data
on a stub can create reflections back down the bus.
These reflections can cause data errors by eroding the
noise margin of the system.
Although stubs are unavoidable in a multidrop system,
care should be taken to keep these stubs as small as
possible, especially in high-speed mode. In slope-con-
trol mode, the requirements are not as rigorous, but
stub length should still be minimized.
Power Supply and Bypassing
The MAX3051 requires no special layout considerations
beyond common practices. Bypass VCC to GND with a
0.1F ceramic capacitor mounted close to the IC with
short lead lengths and wide trace widths.
CONDITION FORCED AT PIN RS
MODE
RESULTING CURRENT AT RS
VRS < 0.3 x VCC
High Speed
|IRS| < 500A
0.4 x VCC <VRS < 0.6 x VCC
Slope Control
10A < |IRS| < 200A
VRS > 0.75 x VCC
Standby
|IRS| < 10A
Table 2. Mode Selection Truth Table
相關PDF資料
PDF描述
MAX3053ESA+T IC TXRX CAN 2MBPS 8-SOIC
MAX3055ASD+T IC TXRX CAN FP 14-SOIC
MAX3059ASA IC TXRX CAN 1MBPS 8-SOIC
MAX3060EEKA#TG16 IC TXRX RS485/422 20MBPS SOT23-8
MAX3071EASA IC TXRX RS485/422 8-SOIC
相關代理商/技術參數
參數描述
MAX3053ASA 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MAX3053ASA+ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MAX3053ASA+T 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MAX3053ASA-T 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MAX3053ESA 制造商:Maxim Integrated Products 功能描述:+/-80V FAULT-PROTECTED, 2MBPS, LOW-SUPPLY CUR - Rail/Tube