- 您現在的位置：買賣IC網 > PDF目錄385522 > MAX181 (Maxim Integrated Products, Inc.) Completed ,8 Channel 12 Bits Data Acquisition System(100ksps,8通道，并行，12位A/D轉換器) PDF資料下載
參數資料
| 型號： | MAX181 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Completed ,8 Channel 12 Bits Data Acquisition System(100ksps,8通道，并行，12位A/D轉換器) |
| 中文描述： | 完備的100ksps、8通道、12位數據采集系統 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 154K |
| 代理商： | MAX181 |
M
Complete, 8-Channel,
12-Bit Data-Ac quisition S ystems
_______________________________________________________________________________________
7
3.0 QUALITY ASSURANCE
3.1
Sampling and inspection procedures shall be in accordance with MIL-M-38510 and, to the extent
specified, with MIL-STD-883.
3.2
Screening shall be in accordance with Method 5004 of MIL-STD-883. Burn-in test (Method 1015):
(1) Test condition A, B, C, or D.
(2) T
A
= +125°C, minimum.
(3) Interim and final electrical test requirements shall be as specified in Table 3.
3.3
Quality conformance inspection shall be in accordance with Method 5005 of MIL-STD-883 includ-
ing Groups A, B, C and D inspection.
Group A inspection:
(1) Tests as specified in Table 3.
(2) Selected subgroups in Tables 1 and 2, Method 5005 of MIL-STD-883 shall be omitted.
(3) Subgroup 4 (C
IN
and C
OUT
) shall be measured only for the initial test and after process or
design changes, which may affect input or output capacitance.
3.4
Groups C and D inspections:
a.
End-point electrical parameters shall be specified in Tables 1 and 2.
b. Steady-state life test (Method 1005 of MIL-STD-883):
(1) Test conditions A, B, C, or D.
(2) T
A
= +125°C, minimum.
(3) Test duration, 1000 hours, except as permitted by Method 1005 of MIL-STD-883.
TABLE 3. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 Test Requirements
Subgroups
(per Method 5005, Tables 1 and 2)
Interim Electrical Parameters
(Method 5004)
1
Final Electrical Parameters
(Method 5004)
1,*2, 3, 9
Group A Test Requirements
(Method 5005)
1, 2, 3 ,4,** 9
Groups C and D End-Point Electrical Parameters
(Method 5005)
1
Additional Electrical Subgroups for Group C Periodic
Inspections
1
*PDA applies to Subgroup 1 only.
**Subgroup 4 shall be tested at initial qualification and upon redesign. Sample size will be 5 units.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1852 | SC70 Inverting Charge Pumps with Shutdown |
| MAX1852EXT | SC70 Inverting Charge Pumps with Shutdown |
| MAX1853 | SC70 Inverting Charge Pumps with Shutdown |
| MAX1853EXT | SC70 Inverting Charge Pumps with Shutdown |
| MAX185 | High Speed 12Bits ADC with T/H and Refereance(10μs,單通道，12位ADC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1810ESA | 功能描述:線性穩壓器 - 標準 RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX1810ESA+ | 功能描述:線性穩壓器 - 標準 Network Interface Card Smart Reg RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX1810ESA+T | 功能描述:線性穩壓器 - 標準 Network Interface Card Smart Reg RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX1810ESA-T | 功能描述:其他電源管理 RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel |
| MAX1811ESA | 功能描述:電池管理 USB-Powered Li+ Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。