參數資料
型號： MAX1644
廠商： Maxim Integrated Products, Inc.
英文描述： Advanced Chemistry-Independent, Level 2 Battery Charger with Input Current Limiting
中文描述： 2A、低電壓、降壓型穩壓器，內置同步整流與開關
文件頁數： 19/32頁
文件大?。?/td> 183K
代理商： MAX1644
M
Advanc ed Chemistry-Independent, Level 2
Battery Charger with Input Current Limiting
______________________________________________________________________________________
19
NAME
FUNCTION
0
CHARGE_INHIBITED
0* = Ready to charge Smart Battery.
1 = Charger is inhibited, I(chg) = 0mA.
This status bit returns the value of the CHG_INHIBITED flip-flop.
1
MASTER_MODE
Always returns “0”
BIT
2
VOLTAGE_NOT_REG
0 = Battery voltage is limited at the set point.
1 = Battery voltage is less than the set point.
3
CURRENT_NOT_REG
0 = Battery current is limited at the set point.
1 = Battery current is less than the set point.
7
VOLTAGE_OR
0 = The ChargingVoltage() value is valid for the MAX1645.
1* = The ChargingVoltage() value exceeds the MAX1645 output range, i.e.,
programmed ChargingVoltage() exceeds 1843mV.
6
CURRENT_OR
0* = The ChargingCurrent() value is valid for the MAX1645.
1 = The ChargingCurrent() value exceeds the MAX1645 output range, i.e.,
programmed ChargingCurrent() exceeds 3008mA.
5
LEVEL_3
Always returns a “0”
4
LEVEL_2
Always returns a “1”
12
ALARM_INHIBITED
Returns the state of the ALARM_INHIBITED flip-flop. This flip-flop is set by either a
watchdog timeout or by writing an AlarmWarning() command with bits 11, 12, 13, 14,
or 15 set. This flip-flop is cleared by BATTERY_PRESENT = 0, writing a “1” into the
POR_RESET bit in the ChargerMode() command, or by receiving successive
ChargingVoltage() and ChargingCurrent() commands. POR: 0.
11
THERMISTOR_UR
0 = THM is > 7.5% of the reference voltage.
1 = THM is < 7.5% of the reference voltage.
10
THERMISTOR_HOT
0 = THM has not dropped to < 23.5% of the reference voltage.
1 = THM has dropped to < 23.5% of the reference voltage.
THERMISTOR_HOT flip-flop cleared by BATTERY_PRESENT = 0 or writing a “1” into
the POR_RESET bit in the ChargerMode() command.
9
THERMISTOR_COLD
0 = THM is < 75.5% of the reference voltage.
1 = THM is > 75.5% of the reference voltage.
8
THERMISTOR_OR
0 = THM is < 91% of the reference voltage.
1 = THM is > 91% of the reference voltage.
Table 3. ChargerStatus()
15
AC_PRESENT
0 = DCIN is below the 7.5V undervoltage threshold.
1 = DCIN is above the 7.5V undervoltage threshold.
14
BATTERY_PRESENT
0 = No battery is present (based on THM input).
1 = Battery is present (based on THM input).
13
POWER_FAIL
0 = The charging source voltage CVS is above the BATT voltage.
1 = The charging source voltage CVS is below the BATT voltage.
Command: 0x13
*State at chip initial power-on.
相關PDF資料
PDF描述
MAX1645B Advanced Chemistry-Independent, Level 2 Battery Charger with Input Current Limiting
MAX1645BEEI Advanced Chemistry-Independent, Level 2 Battery Charger with Input Current Limiting
MAX1647 Chemistry-Independent Battery Chargers
MAX1648 Chemistry-Independent Battery Chargers
MAX1647-MAX1648 Chemistry-Independent Battery Chargers
相關代理商/技術參數
參數描述
MAX1644EAE 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1644EAE/GH9 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1644EAE/GH9-T 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1644EAE+ 功能描述:直流/直流開關轉換器 2A Step-Dow w/Synch Rectification RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1644EAE+T 功能描述:直流/直流開關轉換器 2A Step-Dow w/Synch Rectification RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*