- 您現在的位置：買賣IC網 > Datasheet目錄42 > MAX1617MEE+T (Maxim Integrated)IC REMOTE/LOCAL TEMP SNSR 16QSOP Datasheet資料下載
參數資料
| 型號： | MAX1617MEE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 248K |
| 描述： | IC REMOTE/LOCAL TEMP SNSR 16QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C，外部傳感器 |
| 精確度： | ±3.5°C 本地（最大），±5°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
13
Remote/Local Temperature Sensor
with SMBus Serial Interface
MAX1617
Maxim Integrated
To check for internal bus collisions, read the status
byte. If the least significant seven bits are ones, discard
the data and read the status byte again. The status bits
LHIGH, LLOW, RHIGH, and RLOW are refreshed on the
SMBus clock edge immediately following the stop con-
dition, so there is no danger of losing temperature-relat-
ed status data as a result of an internal bus collision.
The OPEN status bit (diode continuity fault) is only
refreshed at the beginning of a conversion, so OPEN
data is lost. The ALERT interrupt latch is independent of
the status byte register, so no false alerts are generat-
ed by an internal bus collision.
When auto-converting, if the THIGH and TLOW limits
are close together, its possible for both high-temp and
low-temp status bits to be set, depending on the
amount of time between status read operations (espe-
cially when converting at the fastest rate). In these cir-
cumstances, its best not to rely on the status bits to
indicate reversals in long-term temperature changes
and instead use a current temperature reading to
establish the trend direction.
Conversion Rate Byte
The conversion rate register (Table 7) programs the
time interval between conversions in free-running auto-
convert mode. This variable rate control reduces the
supply current in portable-equipment applications. The
conversion rate bytes POR state is 02h (0.25Hz). The
MAX1617 looks only at the 3 LSB bits of this register, so
the upper 5 bits are dont care bits, which should be
set to zero. The conversion rate tolerance is ?5% at
any rate setting.
Valid A/D conversion results for both channels are
available one total conversion time (125ms nominal,
156ms maximum) after initiating a conversion, whether
conversion is initiated via the RUN/STOP bit, hardware
STBY pin, one-shot command, or initial power-up.
Changing the conversion rate can also affect the delay
until new results are available. See Table 8.
RUN/
STOP
6
0
0
POR
STATE
Standby mode control
bit. If high, the device
immediately stops con-
verting and enters stand-
by mode. If low, the
device converts in either
one-shot or timer mode.
Masks all ALERT inter-
rupts when high.
FUNCTION
RFU
50
0
Reserved for future use
MASK
7 (MSB)
BIT
NAME
Table 5. Configuration-Byte Bit
Assignments
Table 7. Conversion-Rate Control Byte
Table 6. Status-Byte Bit Assignments
*These flags stay high until cleared by POR, or until the status
byte register is read.
LHIGH*
6
A high indicates that the local high-
temperature alarm has activated.
A high indicates that the ADC is busy
converting.
FUNCTION
LLOW*
5
A high indicates that the local low-
temperature alarm has activated.
RHIGH*
4
A high indicates that the remote high-
temperature alarm has activated.
RLOW*
3
A high indicates that the remote low-
temperature alarm has activated.
OPEN*
2
A high indicates a remote-diode conti-
nuity (open-circuit) fault.
RFU
1
BUSY
7
(MSB)
Reserved for future use (returns 0)
RFU
0
(LSB)
Reserved for future use (returns 0)
BIT
NAME
0.125
01h
33
30
0.25
02h
35
0.5
03h
48
1
04h
70
2
05h
128
4
06h
0.0625
00h
225
8
07h
425
RFU
08h to
FFh
DATA
CONVERSION
RATE
(Hz)
AVERAGE SUPPLY
CURRENT
(礎 typ, at V
CC
= 3.3V)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1619MEE+ | IC TEMP SENSOR W/ALARM 16-QSOP |
| MAX1765EUE+ | IC REG DL BST/LINEAR 16TSSOP |
| MAX1989MUE+ | IC TEMP SENSOR REMOTE 16TSSOP |
| MAX31723MUA+ | IC THERMOMETER/STAT SPI-3W 8UMAX |
| MAX31826MUA+T | IC TEMP SENSOR DIGITAL 8UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1617MEE-TG075 | 制造商:Maxim Integrated Products 功能描述: |
| MAX1618EVKIT | 制造商:Maxim Integrated Products 功能描述:REMOTE TEMPERATURE SENSOR WITH SMBUS SERIAL I - Bulk |
| MAX1618MUB | 功能描述:板上安裝溫度傳感器 Sensors, Transducers RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1618MUB+ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1618MUB+T | 功能描述:板上安裝溫度傳感器 Sensors, Transducers RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。