- 您現在的位置：買賣IC網 > PDF目錄9508 > MAX15500GTJ+ (Maxim Integrated Products)IC COND ANLG OUT 4.096V 32-TQFN PDF資料下載
參數資料
| 型號： | MAX15500GTJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COND ANLG OUT 4.096V 32-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 類型： | 調節器 |
| 數據接口： | 串行，SPI? |
| 電壓電源： | 模擬和數字，雙 ± |
| 電源電壓： | ±24V，2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1424 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Industrial Analog Current/
Voltage-Output Conditioners
MAX15500/MAX15501
______________________________________________________________________________________ 17
Output Monitor
The MON output provides an analog voltage signal
proportional to the output voltage in current mode and
proportional to the output current in voltage mode. Use
this signal to measure the system load presented to the
output. The full-scale signal on MON is 3V with a typical
accuracy of 10%. The signal range is typically 1.5V to 3V
in unipolar mode and 0 to 3V in bipolar mode.
In current mode, the MAX15500/MAX15501 program IOUT
and monitor the voltage at SENSERN.
VMON = 1.425V + (VSENSERN/20)
RLOAD = ((VMON - 1.425V) x 20)/IOUT(PROGRAMMED)
In voltage mode, the MAX15500/MAX15501 program
VOUT and monitor IOUT.
VMON = 1.521V + 62.4 x ILOAD
RLOAD = VOUT(PROGRAMMED)/((VMON - 1.521V)/62.4)
Error Handling
Many industrial control systems require error detection
and handling. The MAX15500/MAX15501 provide exten-
sive error status reporting.
An open-drain interrupt flag output, ERROR, pulls low
when an error condition is detected. An error register
stores the error source. Reading the error register once
resets the ERROR pin but not the error register itself,
allowing the system to determine the source of the error
and take steps to fix the error condition. After the error
condition has been fixed, read the error register for the
second time to allow the device to clear the error reg-
ister. Read the error register for the third time to verify
if the error register has been cleared. If another error
occurs after the first read, ERROR goes low again. More
information on reading and clearing the error register is
described in the SPI Interface section.
When an output short-circuit or output open-load error
occurs and disappears before the error register is read,
the intermittent bit is set in the error register. The intermit-
tent bit does not assert for brownout and overtempera-
ture error conditions.
Error Conditions
Output Short Circuit
The output short-circuit error bit asserts when the output
current exceeds 30mA (typ) for longer than 260ms. In
current mode, this error occurs when the sense resistor
is shorted and the sense voltage is not equal to 0V. In
voltage mode, this error occurs when the load is shorted
to the supply or ground. The short-circuit error activates
the intermittent bit in the error register if the error goes
away before the error register is read.
VAIN
VOUT OR IOUT
FS + 20%
FS + 5%
FS
5%FS
FSMODE = DGND
FSMODE = DVDD
Figure 1. Unipolar Transfer Function
VAIN
VOUT OR IOUT
FS + 20%
FS + 5%
-FS - 20%
-FS - 5%
FSMODE = DGND
FSMODE = DVDD
50%FS
FS
-FS
Figure 2. Bipolar Transfer Function
相關PDF資料 |
PDF描述 |
|---|---|
| V110A8M200BL3 | CONVERTER MOD DC/DC 8V 200W |
| AD7142ACPZ-1REEL | IC CAP-TO-DGTL CONV PROG 32LFCSP |
| V110A8M200BL2 | CONVERTER MOD DC/DC 8V 200W |
| CS3106A-24-67P | CONN PLUG 19POS STRAIGHT W/PINS |
| V110A8M200BL | CONVERTER MOD DC/DC 8V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX15500GTJ+ | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX15500GTJ+T | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX15501EVKIT+ | 功能描述:數據轉換 IC 開發工具 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX15501GTJ+ | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX15501GTJ+T | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。