參數資料
型號： MAX1514ETP
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 穩壓器
英文描述： TFT-LCD Power-Supply Controllers
中文描述： SWITCHING CONTROLLER, 1725 kHz SWITCHING FREQ-MAX, PQCC20
封裝： 4 X 4 MM, 0.80 MM HEIGHT, MO-220-VGGD, TQFN-20
文件頁數： 23/28頁
文件大?。?/td> 540K
代理商： MAX1514ETP
M
TFT-LCD Power-Supply Controllers
______________________________________________________________________________________
23
determines the frequency placement of the zero and
pole. A typical value of C1 is between 100pF and 10nF.
When adding lead compensation, always check the
loop stability by monitoring the transient response to a
pulsed output load.
Adding lag compensation (the R4/C2 network from FB
to ground in Figure 11) decreases the loop bandwidth
and improves FB noise immunity. Lag compensation
slows the transient response but can increase the stabil-
ity margin, which may be needed for particular compo-
nent choice or high values of FB-divider resistors. Lag
compensation adds a pole-zero pair, attenuating gain at
higher frequencies and lowering loop bandwidth. The
frequencies of the pole and zero for lag compensation
depend on the feedback-divider resistors and the RC
network between FB and GND. The frequencies of the
pole and zero for the lag compensation are:
At high frequencies, R4 is effectively in parallel with R2,
increasing the divider attenuation ratio. If R4 is very
large, the attenuation ratio remains unchanged and as
R4 approaches zero, the attenuation ratio approaches
infinity. A typical value for R4 is greater than 0.1 times
R2. If high-value divider-resistors are used, choose R4
< 1.5k
for FB noise immunity. The value of C2 deter-
mines the frequency placement of the pole and zero. A
typical value of C2 is between 100pF and 1000pF.
When adding lag compensation, always check the loop
stability by monitoring the transient response to a
pulsed output load.
Using Lead Compensation to Reduce
Startup Inrush Current
The digital soft-start of the main step-up regulator limits
the average input current during startup. If even
smoother startup is needed, add a low-frequency lead-
compensation network (Figure 12). The improved soft-
start is active only during soft-start when the output
voltage rises. Positive changes in the output are instan-
taneously coupled to the FB pin through D1 and the
feed-forward capacitor C1. This arrangement gener-
ates a smoothly rising output voltage. When the output
voltage reaches regulation, capacitor C1 charges up
through R3 and diode D1 turns off. If desired, C1 and
R3 can be chosen to also provide some lead compen-
sation in normal operation. In most applications, lead
compensation in normal operation is not needed and
can be avoided by making R3 large. With R3 much
greater than R1, the pole and the zero in the compen-
sation network are very close to one another after start-
up and cancel out, eliminating the effect of the lead
compensation. With R2 at 10k
, an effective value for
C1 is approximately 1000pF.
Charge Pumps
f
R
R
R
R
R
C
f
R
C
P LAG
_
Z LAG
_
×
+
1
×
×
×
=
+
×
=
1
1
2
4
2
2
2
1
4
2
2
π
π
MAX1513
MAX1514
R1
R2
R3
R4
C1
C2
C
OUT
R
LOAD
V
MAIN
FB
GND
V
IN
L
D
LX
Figure 11. Feedback Compensation
MAX1513
MAX1514
R1
R2
R3
C1
C
OUT
V
MAIN
FB
GND
V
IN
L
D
LX
D1
Figure 12. Using Lead Compensation for Improved Soft-Start
相關PDF資料
PDF描述
MAX1518B TFT-LCD DC-DC Converter with Operational Amplifiers
MAX1518BETJ TFT-LCD DC-DC Converter with Operational Amplifiers
MAX1538ETI Power-Source Selector for Dual-Battery Systems
MAX154 CMOS High-Speed 4-Bit ADCs with Multiplexer and Reference(8位,4通道,400ksps,并行A/D轉換器)
MAX1558 Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset
相關代理商/技術參數
參數描述
MAX1514ETP+T 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1514ETP-T 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1515ETG 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515ETG+ 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515ETG+T 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*