- 您現在的位置：買賣IC網 > PDF目錄9952 > MAX149BEAP+T (Maxim Integrated Products)IC ADC 10BIT SERIAL 20-SSOP PDF資料下載
參數資料
| 型號： | MAX149BEAP+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 23/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT SERIAL 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 133k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 640mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
+2.7V to +5.25V, Low-Power, 8-Channel,
Serial 10-Bit ADCs
MAX148/MAX149
9
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal, and is also the minimum time needed for the
signal to be acquired. It is calculated by the following
equation:
tACQ = 7 x (RS + RIN) x 16pF
where RIN = 9kI, RS = the source impedance of the
input signal, and tACQ is never less than 1.5Fs. Note that
source impedances below 4kI do not significantly affect
the ADC’s AC performance.
Higher source impedances can be used if a 0.01FF
capacitor is connected to the individual analog inputs.
Note that the input capacitor forms an RC filter with
the input source impedance, limiting the ADC’s signal
bandwidth.
Input Bandwidth
The ADC’s input tracking circuitry has a 2.25MHz
small-signal bandwidth, so it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate
by using undersampling techniques. To avoid high-
frequency signals being aliased into the frequency band
of interest, anti-alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog
input to VDD and AGND, allow the channel input pins to
swing from AGND - 0.3V to VDD + 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed VDD by more than 50mV or be
lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of off
channels over 2mA.
Quick Look
To quickly evaluate the MAX148/MAX149’s analog per-
formance, use the circuit of Figure 5. The MAX148/
MAX149 require a control byte to be written to DIN
before each conversion. Tying DIN to +3V feeds in
control bytes of $FF (HEX), which trigger single-ended
unipolar conversions on CH7 in external clock mode
without powering down between conversions. In external
clock mode, the SSTRB output pulses high for one clock
period before the most significant bit of the conversion
result is shifted out of DOUT. Varying the analog input to
CH7 will alter the sequence of bits from DOUT. A total of
15 clock cycles is required per conversion. All transitions
of the SSTRB and DOUT outputs occur on the falling
edge of SCLK.
Figure 5. Quick-Look Circuit
MAX148
MAX149
0.1F
VDD
DGND
AGND
COM
SCLK
DIN
DOUT
SSTRB
+3V
N.C.
0.01F
CH7
+3V
REFADJ
VREF
C1
0.1F
0 TO
+2.500V
ANALOG
INPUT
OSCILLOSCOPE
CH1
CH2
CH3
CH4
*FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF (HEX)
OPTIONAL FOR MAX149,
REQUIRED FOR MAX148
+3V
2MHz
OSCILLATOR
SCLK
SSTRB
DOUT*
2.5V
1000pF
COMP
VOUT
+3V
MAX872
SHDN
CS
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72815LB15BG8 | IC FIFO SYNC DUAL 512X18 121BGA |
| V72B36M250BG3 | CONVERTER MOD DC/DC 36V 250W |
| MAX114CAG+T | IC ADC 8BIT 1MSPS 24-SSOP |
| VI-B5F-IV-F3 | CONVERTER MOD DC/DC 72V 150W |
| VI-B5F-IV-F1 | CONVERTER MOD DC/DC 72V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX149BEAP-TG071 | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149BEPP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149BEPP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149BMAP/PR | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149BMAP/PR2 | 制造商:Maxim Integrated Products 功能描述:A/D CONVERTER, 10-BIT, SERIAL, 8-CHANNEL - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。