- 您現在的位置：買賣IC網 > PDF目錄9907 > MAX1415EPE+ (Maxim Integrated Products)IC ADC 16BIT DELTA SIGMA 16-DIP PDF資料下載
參數資料
| 型號： | MAX1415EPE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 24/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT DELTA SIGMA 16-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 25 |
| 位數： | 16 |
| 采樣率（每秒）： | 500 |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 842mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -45°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個差分，單極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX1415/MAX1416
Using FSYNC
When FSYNC = 1, the digital filter and analog modula-
tor are in a reset state, inhibiting normal operation. Set
FSYNC = 0 to begin calibration or conversion.
When configured for normal operation (MD1 and MD0
set to 0),
DRDY goes low 3 x 1/output data rate after
FSYNC goes low to indicate that the new conversion
result is ready to be read from the data register.
DRDY
returns high when a read operation on the data register
is complete. As long as FSYNC remains low, the
MAX1415/MAX1416 perform free-running conversions
with the data registers updating at the output data rate.
If the valid data is not read before the next conversion
result is ready,
DRDY returns high for 500 x 1/fCLKIN
before going low again to indicate a new conversion.
Set FSYNC = 1 to stop converting data.
If FSYNC goes high while
DRDY is low (indicating that
valid data has not yet been read from the data regis-
ter),
DRDY does not reset high. DRDY remains low until
the new data is read from the data register or until
FSYNC goes low to begin a new conversion.
Table 15 provides the duration-to-mode bits and dura-
tion to
DRDY for each calibration sequence. Duration-to-
mode bits provide the time required for the calibration
sequence to complete (MD1 and MD0 return to 0).
Duration to
DRDY provides the time until the first conver-
sion result is valid in the data register (
DRDY goes low).
The pipeline delay necessary to ensure that the first
conversion result is valid is tP (tP = 2000 x 1/fCLKIN).
When selecting self-calibration (MD1 = 0, MD0 = 1),
DRDY goes low 9 x 1/output data rate + tP after FSYNC
goes low (or after a write operation to the setup register
with MD1 = 0 and MD0 = 1 is performed while FSYNC
is already low) to indicate new data in the data register.
When zero-scale or full-scale calibration is selected,
DRDY goes low 4 x 1/output data rate + tP after FSYNC
goes low (or while the zero-scale or full-scale calibra-
tion command is issued when FSYNC is already low) to
indicate new data in the data register (see the
Calibration section).
Calibration
To compensate for errors introduced by temperature
variations or system DC offsets, perform an on-chip cal-
ibration. Select calibration options by writing to the
MD1 and MD0 bits in the setup register (Table 9).
Calibration removes gain and offset errors from the
device and/or the system. Recalibrate with changes in
ambient temperature, supply voltage, bipolar/unipolar
mode, buffered/unbuffered mode, PGA gain, and out-
put data rate.
The MAX1415/MAX1416 offer two calibration modes,
self-calibration and system calibration. The channels of
the MAX1415/MAX1416 are independently calibrated
(see Table 8). The calibration coefficients resulting from
a calibration sequence on a selected channel are stored
in the corresponding offset and gain register pair.
Self- and system calibration automatically calculate the
offset and gain coefficients, which are written to the off-
set and gain registers. These offset and gain coeffi-
cients provide offset and gain error correction for the
specified channel.
Self-Calibration
Self-calibration compensates for offset and gain errors
internal to the ADC. Prior to calibration, set the PGA gain,
unipolar/bipolar mode, buffered/unbuffered mode, and
input channel setting. During self-calibration, AIN+ and
AIN- of the selected channel are internally shorted
together. The ADC calibrates this condition as the zero-
scale output level. For bipolar mode, this zero-scale
point is the midscale of the bipolar transfer function.
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
30
______________________________________________________________________________________
Table 15. Calibration Sequences
CALIBRATION TYPE
(MD1, MD0)
CALIBRATION SEQUENCE
DURATION-TO-MODE
BITS*
DURATION TO
DRDY**
Self-calibration (0,1)
Internal zero-scale calibration at
selected gain plus internal full-
scale calibration at selected gain
6 x 1/output data rate
9 x 1/output data rate + tP
Zero-scale system calibration (1,0)
Zero-scale calibration on AIN at
selected gain
3 x 1/output data rate
4 x 1/output data rate + tP
Full-scale system calibration (1,1)
Full-scale calibration on AIN at
selected gain
3 x 1/output data rate
4 x 1/output data rate + tP
*Duration-to-mode bits represents the completion of the calibration sequence.
**Duration to
DRDY represents the time at which a new conversion result is available in the data register.
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3241ECBZ | IC 3DRVR/5RCVR RS232 3V 28-SOIC |
| MAX1290BCEI+T | IC ADC 12BIT 400KSPS 28-QSOP |
| V48A15T500B3 | CONVERTER MOD DC/DC 15V 500W |
| MAX1291BCEI+T | IC ADC 12BIT 250KSPS 28-QSOP |
| ICL3241ECAZ | IC 3DRVR/5RCVR RS232 3V 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1415EPE+ | 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE+ | 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE+T | 功能描述:模數轉換器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1415EUE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。