- 您現在的位置：買賣IC網 > PDF目錄9921 > MAX1364EUB+ (Maxim Integrated Products)IC SYSTEM MON 12BIT 4CH 10-UMAX PDF資料下載
參數資料
| 型號： | MAX1364EUB+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/25頁 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MON 12BIT 4CH 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 12 |
| 采樣率（每秒）： | 133k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 444.4mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極 |
MAX1363/MAX1364
When the MAX1363/MAX1364 receive a NACK, they
release SDA allowing the master to generate a STOP or
a repeated START condition.
Monitor Mode
Monitor-Mode Overview
The MAX1363/MAX1364 automatically monitor up to four
input channels. For systems with limited I2C bandwidth,
monitor mode allows the C to set a window by
programming lower and upper thresholds during initial-
ization, and only intervening if the MAX1363/MAX1364
detect an alarm condition. This allows an interrupt-driven
approach as an alternative to continuously polling the
ADC with the C. Monitor mode reduces processor over-
head and conserves I2C bandwidth.
The following shows an example of events in
monitor mode:
1) Fault condition(s) detected,
INT asserted.
2) Host C services interrupt and sends SMBus alert to
identify the alarming device. The MAX1363/
MAX1364 respond with the I2C slave address, pend-
ing arbitration rules. (See the
SMBus Alert section.)
3) The MAX1363/MAX1364 release the
INT.
4) Host C reads the alarm-status register, latched-
fault register, and current-conversion results to
determine the alarming channel(s) and course
of action.
5) Host C services alarm(s); adjusts system parame-
ters as needed and/or adjusts lower and upper
thresholds.
6) Host C resets the alarming channel. See the
Configuring Monitor Mode section.
7) Monitor mode resumes.
8) If there is still an active fault, the device asserts
INT
again. See step 1.
Writing SCAN1 and SCAN0 bits = [1,0] in the configura-
tion byte activates monitor mode. The MAX1363/
MAX1364 scan from channels 0 up to the channel
selected by [CS1:CS0] at a rate determined by the
scan delay bits. The MAX1363/MAX1364 compare the
conversion results with the lower and upper thresholds
for each channel. When any conversion exceeds the
threshold, the MAX1363/MAX1364 assert an interrupt
by pulling
INT low (if enabled). The MAX1363/
MAX1364 set the corresponding flag bit in the alarm-
status register and write conversion results to the
latched-fault register to record the event causing the
alarm condition.
INT active state is randomly delayed with respect to the
conversion. Depending on the number of channels
scanned and the position in the channel scan sequence,
the maximum possible delay for asserting
INT is five con-
version periods (37.5s typ, Delay = 0,0,0).
Configuring Monitor Mode
To write monitoring setup data, set the monitor-setup bit
(bit 0 in setup byte) to 1 to extend writing up to 104 bits
(13 bytes) of monitoring setup data. The number of bits
written to the MAX1363/MAX1364 depends on whether
the part is in single-ended or differential mode and
whether the upper channel limit is set by [CS1:CS0]
(Table 9).
Terminate writing at any time by using a STOP or
repeated START condition. Previous monitoring setup
data not overwritten remains valid.
A 1 written to the reset alarm CH_ clears the alarm, oth-
erwise no action occurs (Table 10). Deassert
INT by
4-Channel, 12-Bit System Monitors with Programmable
Trip Window and SMBus Alert Response
18
______________________________________________________________________________________
ACK
1, CH ADD, 10b/12b,
RESULT (4 MSBs)
RESULT N (8 LSBs)
tACQ
CONVERSION 1
tACQ
CONVERSION N
START
ADDRESS
FROM THE MASTER
1, CH ADD, 10b/12b
RESULT (4 MSBs)
RESULT (8 LSBs)
1
ACK
Figure 13. Example of Scan-Mode Conversions Using the External Clock, SCAN = 0,0 and 0,1
相關PDF資料 |
PDF描述 |
|---|---|
| ISL32372EFBZ-T | IC XMITTER ESD RS422 LP 16-SOIC |
| MX7574JCWN+T | IC ADC 8BIT MPU COMP 18-SOIC |
| MAX1203BCAP+T | IC ADC 12BIT 8CH 20-SSOP |
| VI-2W1-MX-F1 | CONVERTER MOD DC/DC 12V 75W |
| ISL32274EIVZ-T | IC XMITTER ESD RS422 LP 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1364EUB+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1364EUB+T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1364EUB-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1364EUT-T | 制造商:Maxim Integrated Products 功能描述:12-BIT, 4-CHANNEL ANALOG-TO-DIGITAL CONVERTERS - Tape and Reel |
| MAX1364LEUB+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 133KSPS 12-BIT SERL 10PIN UMAX - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。