- 您現在的位置：買賣IC網 > PDF目錄10648 > MAX13487EESA+ (Maxim Integrated Products)IC TXRX RS485/422 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13487EESA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS485/422 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1408 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
on M2 and sets the SR latch, which also turns on M1.
Transistors M2, a 1.5mA current source, and M1, a 500A
current source, pull RE to VCC through a 5k
Ω resistor. M2
is designed to pull RE to the disabled state against an
external parasitic capacitance up to 100pF that can drive
RE high. After 15s, the timer deactivates M2 while M1
remains on, holding DI high against three-state leakages
that can drive RE low. M1 remains on until an external
source overcomes the required input current. At this time,
the SR latch resets and M1 turns off. When M1 turns off,
RE reverts to a standard, high-impedance CMOS input.
Whenever VCC drops below 1V, the hot-swap input is
reset. DI has similar hot-swap circuitry.
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges encountered during handling and
assembly. The driver outputs and receiver inputs of the
MAX13487E/MAX13488E have extra protection against
static electricity. Maxim’s engineers have developed
state-of-the-art structures to protect these pins against
ESD of ±15kV without damage. The ESD structures
withstand high ESD in all states: normal operation, shut-
down, and powered down. After an ESD event, the
MAX13487E/MAX13488E keep working without latchup
or damage.
ESD protection can be tested in various ways. The
transmitter outputs and receiver inputs of the
MAX13487E/MAX13488E are characterized for protec-
tion to the following limits:
±15kV using the Human Body Model
±15kV using the Air Gap Discharge Method speci-
fied in IEC 61000-4-2 (MAX13487E only)
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 10a shows the Human Body Model, and Figure
10b shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the test device
through a 1.5k
Ω resistor.
IEC 61000-4-2
The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment. However, it does
not specifically refer to integrated circuits. The
MAX13487E/MAX13488E help you design equipment to
meet IEC 61000-4-2 without the need for additional
ESD-protection components.
The major difference between tests done using the
Human Body Model and IEC 61000-4-2 is higher peak
current in IEC 61000-4-2 because series resistance is
lower in the IEC 61000-4-2 model. Hence, the ESD
withstand voltage measured to IEC 61000-4-2 is gener-
ally lower than that measured using the Human Body
Model. Figure 10c shows the IEC 61000-4-2 model,
and Figure 10d shows the current waveform for IEC
61000-4-2 ESD Contact Discharge test.
Machine Model
The machine model for ESD tests all pins using a 200pF
storage capacitor and zero discharge resistance.
The objective is to emulate the stress caused when I/O
pins are contacted by handling equipment during test
and assembly. Of course, all pins require this protec-
tion, not just RS-485 inputs and outputs.
The Air-Gap test involves approaching the device with a
charged probe. The Contact-Discharge method connects
the probe to the device before the probe is energized.
MAX13487E/MAX13488E
Half-Duplex RS-485-/RS-422-Compatible
Transceiver with AutoDirection Control
______________________________________________________________________________________
13
VCC
M1
M2
100
μA
500
μA
5k
Ω
SR LATCH
15
μs
VCC
TIMER
RE
(HOT SWAP)
RE
Figure 9. Simplified Structure of the Receiver Enable Pin (RE)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J5X-MY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
| MAX990ESA+ | IC COMPARATOR R-R 8-SOIC |
| VE-21P-IW-F4 | CONVERTER MOD DC/DC 13.8V 100W |
| VI-2WY-MV | CONVERTER MOD DC/DC 3.3V 99W |
| VE-J5X-MY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13487EESA+ | 功能描述:RS-422/RS-485 接口 IC Half-Dplx RS-485/422 5V 500ksps LD/Rc RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX13487EESA+T | 功能描述:RS-422/RS-485 接口 IC Half-Dplx RS-485/422 5V 500ksps LD/Rc RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX13487EEVKIT# | 功能描述:界面開發工具 MAX13487E Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX13488EESA+ | 功能描述:RS-422/RS-485 接口 IC Half-Dplx RS-485/422 5V 16Msps LD/Rc RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX13488EESA+T | 功能描述:RS-422/RS-485 接口 IC Half-Dplx RS-485/422 5V 16Msps LD/Rc RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。