- 您現在的位置：買賣IC網 > PDF目錄10492 > MAX132CNG+ (Maxim Integrated Products)IC ADC 18BIT W/SRL INTRFC 24-DIP PDF資料下載
參數資料
| 型號： | MAX132CNG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT W/SRL INTRFC 24-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 15 |
| 位數： | 18 |
| 采樣率（每秒）： | 100 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，雙極 |
| 產品目錄頁面： | 1393 (CN2011-ZH PDF) |
MAX132
Second Deintegrate Phase
The second deintegrate phase deintegrates residual
voltage on the integration capacitor that has been
through the X8 phase. Since the voltage across the
integration capacitor has been multiplied by 8, each
deintegration clock cycle corresponds to 1/8 of one
clock cycle during the first deintegration.
Additional Times-Eight
and Deintegrate Phases
At the end of the second and third deintegration phas-
es, the device performs a X8 multiplication of the resid-
ual voltage left on the integration capacitor. After each
of these X8 multiplications, a deintegration occurs,
resulting in a second, third, and fourth deintegration
phase. Each time the residual voltage on the integration
capacitor is multiplied by 8, the following deintegration
has 8 times finer resolution.
Zero-Integrate Phase
The zero-integrate phase zeros out the integrator to
prepare for the next integration (Figure 10). This phase
occurs at the beginning and end of each conversion. At
power-up, or in the hold mode prior to a conversion, the
MAX132 continues to zero integrate until a conversion
starts. When a conversion starts in 60Hz mode, another
111 clocks of zero integrate are completed before the
beginning of a conversion. In 50Hz mode, only one
additional zero integrate is performed before the con-
version starts. An additional 20 clocks of zero integrate
occur at each conversion end.
__________Applications Information
Extended Delays Between Conversions
An extended delay between conversions can degrade
the subsequent conversion result due to capacitor
droop and internal offset/common-mode voltages. The
initial reading may be off by 4 to 6 counts in a ±15-bit
configuration. When the delay between conversions
exceeds 2 seconds (either because of a slower conver-
sion rate or the use of sleep mode), it is recommended
that the first reading after this delay be discarded.
Increased Speed
The MAX132 is tested with a 32,768Hz clock frequen-
cy, which results in 16 conv/sec. Up to 96 conv/sec
may be achieved with higher clock frequencies and
some changes in component values, as shown in Table
1. Operation at higher conversion rates reduces accu-
racy, and care must be taken to get the best results.
Although either the 50Hz or 60Hz mode can be used,
complete rejection of 50Hz or 60Hz normal-mode noise
at conversion rates above 16 conv/sec is impossible.
Use the 50Hz mode when operating at more than 16
conv/sec, irrespective of the local line frequency. The
50Hz mode uses a slightly longer integration time than
the 60Hz mode, and generally gives lower-noise perfor-
mance.
Table 1 lists the crystal frequencies and integrating
capacitor values for the 50Hz and 60Hz modes for vari-
ous conversion rates, although the 50Hz mode is rec-
ommended for clock rates above 32,768Hz.
The raw data can be used where highest accuracy is
not required, and the least significant bits can be
ignored. At 96 conv/sec, the accuracy is 13 bits.
Improvements in accuracy can be gained by averaging
both the data and the zero readings, although data
averaging compromises the converter’s speed perfor-
mance.
To maximize throughput, take zero readings only when
necessary, i.e., when the common-mode voltage
changes. It is not normally necessary to take a zero read-
ing after every data reading as an excessive number of
zero readings reduces the converter’s effective speed.
Noise Reduction
To minimize noise, each supply must be bypassed to
GND with a 0.1F capacitor. A ground plane should
also be placed under the analog circuitry. Use the RC
network at the inputs as shown in Figure 6. Also refer to
the section “Noise Reduction Techniques” in the notes
for the MAX132 evaluation kit. To minimize the coupling
effects of stray capacitance, keep digital lines as far
from analog components and lines as possible. Also,
connect the integrator capacitor’s outside foil to the INT
OUT pin to minimize stray capacitive coupling. If possi-
ble, keep the digital interface inactive while the
MAX132 is converting.
Ratiometric Measurements
Figure 11 shows an application to measure tempera-
ture ratiometrically with an RTD sensor. The voltage
drops across the RTD sensor and the 250
reference
resistor are generated by the same current source. The
voltage of the sensor (VS) is fed directly into the differ-
ential inputs, and the voltage drop across the reference
resistor (VR) is brought into the differential reference
inputs. The relationship of these voltages is ratiometric
and unaffected by the actual current. The MAX132’s
output is proportional to VS divided by VR, independent
±18-Bit ADC with Serial Interface
14
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| UP050SL010M-NAC | CAP CER 1PF 50V 20% AXIAL |
| VE-24F-IW-F4 | CONVERTER MOD DC/DC 72V 100W |
| MAX225EWI+G36 | IC RS-232 DRVR/RCVR 28-SOIC |
| UP050SL010M-KFC | CAP CER 1PF 50V 20% AXIAL |
| VE-24F-IW-F3 | CONVERTER MOD DC/DC 72V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX132CNG+ | 功能描述:模數轉換器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX132CWG | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX132CWG+ | 功能描述:模數轉換器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX132CWG+C10203 | 制造商:Maxim Integrated Products 功能描述:?18-BIT ADC WITH SERIAL INTERFACE - Rail/Tube |
| MAX132CWG+T | 功能描述:模數轉換器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。