參數資料
型號： MAX1308ECM+T
廠商： Maxim Integrated Products
文件頁數： 27/37頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 8CH 4MSPS 48LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,000
位數： 12
采樣率（每秒）： 3.65M
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 1.82W
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 帶卷 (TR)
輸入數目和類型： 8 個單端，單極
MAX1304–MAX1306/MAX1308–MAX1310/MAX1312–MAX1314
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
______________________________________________________________________________________
33
Gain Error
Gain error is a figure of merit that indicates how well the
slope of the actual transfer function matches the slope
of the ideal transfer function. For the MAX1304–
MAX1306/MAX1308–MAX1310/MAX1312–MAX1314, the
gain error is the difference of the measured full-scale
and zero-scale transition points minus the difference of
the ideal full-scale and zero-scale transition points.
For the unipolar devices (MAX1304/MAX1305/
MAX1306), the full-scale transition point is from 0xFFE
to 0xFFF and the zero-scale transition point is from
0x000 to 0x001.
For the bipolar devices (MAX1308/MAX1309/MAX1310/
MAX1312/MAX1313/MAX1314), the full-scale transition
point is from 0x7FE to 0x7FF and the zero-scale transi-
tion point is from 0x800 to 0x801.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC’s reso-
lution (N bits):
SNRdB[max] = 6.02dB
× N + 1.76dB
In reality, there are other noise sources such as thermal
noise, reference noise, and clock jitter.
For these devices, SNR is computed by taking the ratio
of the RMS signal to the RMS noise. RMS noise
includes all spectral components to the Nyquist fre-
quency excluding the fundamental, the first five har-
monics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS signal
to the RMS noise plus distortion. RMS noise plus distor-
tion includes all spectral components to the Nyquist fre-
quency excluding the fundamental and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at
a specific input frequency and sampling rate. An ideal
ADC’s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed as:
Total Harmonic Distortion (THD)
THD is the ratio of the RMS sum of the first five harmon-
ics to the fundamental itself. This is expressed as:
where V1 is the fundamental amplitude, and V2 through
V6 are the amplitudes of the 2nd- through 6th-
order harmonics.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio of the RMS amplitude of the fundamen-
tal (maximum signal component) to the RMS value of the
next largest spurious component, excluding DC offset.
SFDR is specified in decibels relative to the carrier (dBc).
Channel-to-Channel Isolation
Channel-to-channel isolation indicates how well each
analog input is isolated from the others. The channel-to-
channel isolation for these devices is measured by
applying DC to channel 1 through channel 7 while an
AC 500kHz, -0.4dBFS sine wave is applied to channel
0. An FFT is taken for channel 0 and channel 1 and the
difference (in dB) of the 500kHz magnitudes is reported
as the channel-to-channel isolation.
Aperature Delay
Aperture delay (tAD) is the time delay from the CONVST
rising edge to the instant when an actual sample is taken.
THD
x
VVVV
V
=
+++
+
20
2
3
2
4
2
5
2
6
2
1
log
ENOB
SINAD
=
176
602
.
SINAD dB
x
SIGNAL
NOISE
DISTORTION
RMS
()
log
()
=
+
20
R
RMS
相關PDF資料
PDF描述
MAX1320ECM+T IC ADC 14BIT 8CH 2MSPS 48LQFP
MAX132EWG+T IC ADC 18BIT SERIAL 24-SOIC
MAX135EPI+ IC ADC 15BIT PARALLEL 28-DIP
MAX1361MEUB+T IC SYSTEM MON 10BIT 4CH 10-UMAX
MAX1364MEUB+T IC SYSTEM MON 12BIT 4CH 10-UMAX
相關代理商/技術參數
參數描述
MAX1308EVB16 功能描述:數據轉換 IC 開發工具 MAX1308 Evaluation Kit/Evaluation System RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1308EVKIT 功能描述:數據轉換 IC 開發工具 MAX1308 Evaluation Kit/Evaluation System RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1309ECM 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1309ECM/V+ 功能描述:模數轉換器 - ADC 12-Bit 4Ch 1.075Msps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1309ECM/V+T 功能描述:模數轉換器 - ADC 12-Bit 4Ch 1.075Msps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*