- 您現在的位置：買賣IC網 > PDF目錄10655 > MAX13041ASD+ (Maxim Integrated Products)IC CAN TXRX +/-80V HS 14-SOIC PDF資料下載
參數資料
| 型號： | MAX13041ASD+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/20頁 |
| 文件大小： | 0K |
| 描述： | IC CAN TXRX +/-80V HS 14-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 特色產品： | MAX13041 High-Speed CAN Transceiver |
| 標準包裝： | 50 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1408 (CN2011-ZH PDF) |
MAX13041
Thermal Shutdown Fault
The local failure flag is set when the junction temperature
(TJ) exceeds the shutdown junction temperature thresh-
old, TJ(SD). The transmitter is disabled to prevent exces-
sive current dissipation from damaging the device. The
transmitter remains disabled until TJ drops TJ(SD)HYST
degrees, and the local failure flag is cleared.
Recovering from Local Faults
The local failure flag is cleared and the transmitter is re-
enabled whenever RXD is dominant while TXD is reces-
sive. This situation occurs normally when the MAX13041
is receiving CAN bus data in the absence of a bus failure.
In PWON/listen-only mode,
ERR changes to a logic-high
to reflect the change in the local failure flag. If there is no
activity on the CAN bus, the local failure flag can also be
cleared by switching to normal mode from another oper-
ating mode. A typical method involves switching to
PWON/listen-only mode and reading the local failure flag
on
ERR. Subsequently, switch back to normal mode to
clear the flag. This sequence is then repeated to verify
that the failure has been resolved.
ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges encountered during handling and
assembly. The CANH and CANL lines are further pro-
tected by advanced ESD structures to guard these pins
from damage caused by ESD of up to ±12kV as mea-
sured by the Human Body Model (HBM). Protection
structures prevent damage caused by ESD events in all
operating modes, and when the device is unpowered.
ESD Models
Several ESD testing standards exist for gauging the
robustness of ESD structures. The ESD protection of
the MAX13041 is characterized for the human body
model (HBM). Figure 6 shows the model used to simu-
late an ESD event resulting from contact with the
human body. The model consists of a 100pF storage
capacitor that is charged to a high voltage, and subse-
quently discharged through a 1.5kΩ resistor. Figure 7
shows the current waveform when the storage capaci-
tor is discharged into a low impedance.
ESD Test Conditions
ESD performance depends on a variety of conditions.
Please contact Maxim for a reliability report document-
ing test setup, methodology, and results.
Applications Information
Clamp-30, Type-A CAN Modules
The MAX13041 is primarily intended for automotive
ECU applications where battery power is permanently
supplied to the node (see Figure 8.) This type of appli-
cation is referred to as a clamp-30 node. ECU modules,
which are supplied by the battery only when the ignition
switch is closed, are referred to as clamp-15 modules.
Because clamp-30 modules are permanently supplied
by battery voltage, low power consumption is an essen-
tial design requirement. The MAX13041 provides
advanced power management to the entire node by
controlling one or more external voltage regulators.
While CAN transceivers, such as the MAX13041,
operate from a supply voltage of +5V, many micro-
processors are supplied by voltages of +3.3V and
lower. By controlling the supply voltage regulator for the
microprocessor, the MAX13041 can force a low-power
sleep mode for the entire node.
EMC Considerations
In multidrop CAN applications, it is important to main-
tain a direct point-to-point wiring scheme. A single pair
of wires should connect each transceiver on the CAN
bus, and the bus wires should be properly split-termi-
nated with two 60Ω resistors at each end as described
in Figure 3 . For best EMC performance, do not use a
star topology. Any deviation from the point-to-point
wiring scheme results in a stub. High-speed edges of
the CAN signal reflect from the unterminated stub ends,
interfering with communication on the bus. To minimize
the effect of these reflections, care should be taken to
minimize the length of stubs.
Power-Supply Decoupling
Bypass VCC, VBAT, and VI/O to ground with 0.1F
ceramic capacitors. Place all capacitors as close as
possible to the device.
±80V Fault-Protected High-Speed CAN Transceiver
with Low-Power Management and Wake-On CAN
16
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| 1-213825-4 | CONN CPC RCPT 14POS |
| MAX968ESA+T | IC COMPARATOR R-R 8-SOIC |
| MAX922CSA | IC COMPARATOR DUAL LOWPWR 8-SOIC |
| MAX9041AEUT+T | IC COMPARATOR SNGL SOT23-6 |
| MAX9051AEUT+T | IC COMPARATOR SNGL SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13041ASD/V+ | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13041ASD/V+T | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13041ASD+ | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13041ASD+T | 功能描述:CAN 接口集成電路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13042EEBC+ | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。