參數資料
型號: MAX1299CEAE+
廠商: Maxim Integrated
文件頁數: 18/20頁
文件大?。?/td> 299K
描述: IC TEMP SENS W/ADC 16-SSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 76
功能: 溫度監控系統(傳感器)
傳感器類型: 內部和外部
感應溫度: -40°C ~ 85°C,外部傳感器
精確度: ±4°C(最小值)
拓?fù)洌?/td> ADC,多路復用器,寄存器庫
輸出類型: MICROWIRE?,QSPI?,SPI?
輸出警報:
輸出風扇:
電源電壓: 2.7 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 16-SSOP
包裝: 管件
Layout, Grounding, and Bypassing
For best performance, use PC boards. Do not use wire-
wrap boards. Board layout should ensure that digital
and analog signal lines are separated from each other.
Do not run analog and digital (especially clock) signals
parallel to one another or run digital lines underneath
the ADC package.
High-frequency noise in the V
DD
power supply may
affect ADC performance. Bypass the supply with a
0.1礔 capacitor close to pin V
DD
. Minimize capacitor
lead lengths for best supply-noise rejection. If the
power supply is very noisy, connect a 10& resistor in
series with the supply to provide lowpass filtering.
Definitions
Relative Accuracy
Relative accuracy is the deviation of the values on an
actual transfer function from a straight line. This straight
line can be either a best-straight-line fit or a line drawn
between the endpoints of the transfer function, once
offset and gain errors have been nullified. The static lin-
earity parameters for the MAX1298/MAX1299 are mea-
sured using the best-straight-line-fit method.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step width and the ideal value of 1LSB. A DNL
error specification of less than 1LSB guarantees no
missing codes and a monotonic transfer function.
Offset Error
The offset error is the difference between the ideal and
the actual offset points. For an ADC, the offset point is
the midstep value when the digital output is zero.
Gain Error
The gain or full-scale error is the difference between
the ideal and actual gain points on the transfer function,
after the offset error has been canceled out. For an
ADC, the gain point is the midstep value when the digi-
tal output is full scale.
Aperture Delay
Aperture delay (t
AD
) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken.
Chip Information
PROCESS: BiCMOS
12-Bit Serial-Output Temperature Sensors
with 5-Channel ADC
18   ______________________________________________________________________________________
Figure 8. Remote Diode Shielding for PC Boards
ANODE
SHIELD
CATHODE
相關PDF資料
PDF描述
MAX14544ETA+T IC ACCY SWITCH OVP PROTECT 8TDFN
MAX1617AMEE+T IC REMOTE/LOCAL TEMP SNSR 16QSOP
MAX1617MEE+T IC REMOTE/LOCAL TEMP SNSR 16QSOP
MAX1619MEE+ IC TEMP SENSOR W/ALARM 16-QSOP
MAX1765EUE+ IC REG DL BST/LINEAR 16TSSOP
相關代理商/技術參數
參數描述
MAX1299CEAE+ 功能描述:板上安裝溫度傳感器 12-Bit Serial-Output w/5Ch ADC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX1299CEAE+T 功能描述:板上安裝溫度傳感器 12-Bit Serial-Output w/5Ch ADC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX1299CEAE-T 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX12D 制造商:Lanzar 功能描述:Dual 4 Ohm 1000W Peak 12 Paper Cone Dual Vc Woofer 制造商:LANZAR 功能描述:12 PAPER CONE DUAL VC WOOFER DUAL 4 OHM 1000W PEAK
MAX12G 制造商:Aavid Thermalloy 功能描述:Thrml Mgmt Access Heat Sink Clip