- 您現在的位置：買賣IC網 > PDF目錄9883 > MAX1283BCUE+ (Maxim Integrated Products)IC ADC 12BIT 400KSPS 16-TSSOP PDF資料下載
參數資料
| 型號： | MAX1283BCUE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 400KSPS 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 位數： | 12 |
| 采樣率（每秒）： | 400k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 8.0mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
conversion result). (See Figure 16 for MAX1282/
MAX1283 QSPI connections.)
Simple Software Interface
Make sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 500kHz to 6.4MHz (MAX1282) or
4.8MHz (MAX1283).
1) Set up the control byte and call it TB1. TB1 should
be in the format: 1XXXXXXX binary, where the Xs
denote the particular channel, selected conversion
mode, and power mode.
2) Use a general-purpose I/O line on the CPU to pull
CS low.
3) Transmit TB1 and, simultaneously, receive a byte
and call it RB1. Ignore RB1.
4) Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB2.
5) Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB3.
6) Pull CS high.
Figure 5 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion, padded
with three leading zeros, and one trailing zero. The total
conversion time is a function of the serial-clock fre-
quency and the amount of idle time between 8-bit
transfers. To avoid excessive T/H droop, make sure the
total conversion time does not exceed 120s.
Digital Output
In unipolar input mode, the output is straight binary
(Figure 13). For bipolar input mode, the output is two’s
complement (Figure 14). Data is clocked out on the ris-
ing edge of SCLK in MSB-first format.
Serial Clock
The external clock not only shifts data in and out, but it
also drives the analog-to-digital conversion steps.
SSTRB pulses high for one clock period after the last bit
of the control byte. Successive-approximation bit deci-
sions are made and appear at DOUT on each of the
next 12 SCLK rising edges, MSB first (Figure 5). SSTRB
and DOUT go into a high-impedance state when CS
goes high; after the next CS falling edge, SSTRB out-
puts a logic low. Figure 6 shows the detailed serial-inter-
face timings.
The conversion must complete in 120s or less, or
droop on the sample-and-hold capacitors may degrade
conversion results.
Data Framing
The falling edge of CS does not start a conversion.
The first logic high clocked into DIN is interpreted as a
start bit and defines the first bit of the control byte. A
conversion starts on SCLK’s falling edge, after the eighth
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as follows:
The first high bit clocked into DIN with CS low any
time the converter is idle, e.g., after VDD1 and VDD2
are applied.
or
The first high bit clocked into DIN after B6 of a con-
version in progress is clocked onto the DOUT pin
(Figure 7).
Once a start bit has been recognized, the current conver-
sion may only be terminated by pulling SHDN low.
The fastest the MAX1282/MAX1283 can run with CS held
low between conversions is 16 clocks per conversion.
Figure 7 shows the serial-interface timing necessary to
perform a conversion every 16 SCLK cycles. If CS is tied
low and SCLK is continuous, guarantee a start bit by first
clocking in 16 zeros.
___________Applications Information
Power-On Reset
When power is first applied, and if SHDN is not pulled
low, internal power-on reset circuitry activates the
MAX1282/MAX1283 in normal operating mode, ready to
convert with SSTRB = low. After the power supplies sta-
bilize, the internal reset time is 10s, and no conver-
sions should be performed during this phase. If CS is
low, the first logic 1 on DIN is interpreted as a start bit.
Until a conversion takes place, DOUT shifts out zeros.
Additionally, wait for the reference to stabilize when
using the internal reference.
Power Modes
Save power by placing the converter in one of two low-
current operating modes or in full power-down between
conversions. Select the power-down mode through bit
1 and bit 0 of the DIN control byte (Tables 3 and 4), or
force the converter into hardware shutdown by driving
SHDN to GND.
The software power-down modes take effect after the
conversion is completed; SHDN overrides any software
power mode and immediately stops any conversion in
progress. In software power-down mode, the serial
interface remains active while waiting for a new control
byte to start conversion and switch to full-power mode.
MAX1282/MAX1283
300ksps/400ksps, Single-Supply, 4-Channel,
Serial 12-Bit ADCs with Internal Reference
______________________________________________________________________________________
13
相關PDF資料 |
PDF描述 |
|---|---|
| V300A24T500BG | CONVERTER MOD DC/DC 24V 500W |
| VI-BWD-MW-F1 | CONVERTER MOD DC/DC 85V 100W |
| MAX1080ACUP+ | IC ADC 10BIT 400KSPS 20-TSSOP |
| MAX1081ACUP+ | IC ADC 10BIT 300KSPS 20-TSSOP |
| V300A24T500BF3 | CONVERTER MOD DC/DC 24V 500W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1283BCUE+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 300ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1283BCUE+T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 300ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1283BCUE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1283BEUE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1283BEUE+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 300ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。