- 您現在的位置：買賣IC網 > PDF目錄9888 > MAX1246BEEE (Maxim Integrated Products)IC ADC LP 12-BIT SERIAL 16-QSOP PDF資料下載
參數資料
| 型號： | MAX1246BEEE |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC LP 12-BIT SERIAL 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 位數： | 12 |
| 采樣率（每秒）： | 133k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 667mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極 |
MAX1246/MAX1247
+2.7V, Low-Power, 4-Channel,
Serial 12-Bit ADCs in QSOP-16
______________________________________________________________________________________
11
BIT
NAME
DESCRIPTION
7(MSB)
START
The first logic “1” bit after CS goes low defines the beginning of the control byte.
6
SEL2
These three bits select which of the four channels are used for the conversion (Tables 2 and 3).
5
SEL1
4
SEL0
3
UNI/BIP
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, an
analog input signal from 0V to VREF can be converted; in bipolar mode, the signal can range
from -VREF / 2 to +VREF / 2.
2
SGL/DIF
1 = single ended, 0 = differential. Selects single-ended or differential conversions. In single-
ended mode, input signal voltages are referred to COM. In differential mode, the voltage
difference between two channels is measured (Tables 2 and 3).
1
PD1
Selects clock and power-down modes.
0(LSB)
PD0
PD1
PD0
Mode
0
Full power-down
0
1
Fast power-down
1
0
Internal clock mode
1
External clock mode
Table 1. Control-Byte Format
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal, and is also the minimum time needed for the
signal to be acquired. It is calculated by the following
equation:
tACQ = 9 x (RS + RIN) x 16pF
where RIN = 9k
, RS = the source impedance of the
input signal, and tACQ is never less than 1.5s. Note
that source impedances below 1k
do not significantly
affect the ADC’s AC performance.
Higher source impedances can be used if a 0.01F
capacitor is connected to the individual analog inputs.
Note that the input capacitor forms an RC filter with the
input source impedance, limiting the ADC’s signal
bandwidth.
Input Bandwidth
The ADC’s input tracking circuitry has a 2.25MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog input
to VDD and AGND, allow the channel input pins to swing
from AGND - 0.3V to VDD + 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed VDD by more than 50mV or be
lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over 4mA.
How to Start a Conversion
Start a conversion by clocking a control byte into DIN.
With CS low, each rising edge on SCLK clocks a bit from
DIN into the MAX1246/MAX1247’s internal shift register.
After CS falls, the first arriving logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with no
effect. Table 1 shows the control-byte format.
The MAX1246/MAX1247 are compatible with SPI/
QSPI and Microwire devices. For SPI, select the
correct clock polarity and sampling edge in the SPI
control registers: set CPOL = 0 and CPHA = 0. Micro-
wire, SPI, and QSPI all transmit a byte and receive a
byte at the same time. Using the Typical Operating
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(MSB)
(LSB)
START
SEL2
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
PD0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1249BEPE+ | IC ADC 10BIT SERIAL 16-DIP |
| MS27508E22A35PC | CONN RCPT 100POS BOX MNT W/PINS |
| MAX1249ACPE+ | IC ADC 10BIT SERIAL 16-DIP |
| MAX1068ACEG+T | IC ADC 14BIT 200KSPS 24-QSOP |
| MS27508E22F35PB | CONN RCPT 100POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1246BEEE+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1246BEEE+T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1246BEEE-T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1246BEPE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1246BEPE+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發(fā)布緊急采購，3分鐘左右您將得到回復。