參數資料
型號： MAX1221BETX+
廠商： Maxim Integrated Products
文件頁數： 16/44頁
文件大?。?/td> 0K
描述： IC ADC/DAC 12BIT W/FIFO 36TQFNEP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： ADC，DAC
分辨率（位）： 12 b
采樣率（每秒）： 225k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 2.7 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 36-WFQFN 裸露焊盤
供應商設備封裝： 36-TQFN 裸露焊盤（6x6）
包裝： 管件
MAX1221/MAX1223/MAX1343
12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
23
Clock Modes
Internal Clock
The MAX1221/MAX1223/MAX1343 can operate from an
internal oscillator. The internal oscillator is active in
clock modes 00, 01, and 10. Figures 6, 7, and 8 show
how to start an ADC conversion in the three internally
timed conversion modes.
Read out the data at clock speeds up to 25MHz
through the SPI interface.
External Clock
Set CKSEL1 and CKSEL0 in the setup register to 11 to
set up the interface for external clock mode 11. See
Table 5. Pulse SCLK at speeds from 0.1MHz to
3.6MHz. Write to SCLK with a 40% to 60% duty cycle.
The SCLK frequency controls the conversion timing.
See Figure 9 for clock mode 11 timing. See the
ADC
Conversions in Clock Mode 11 section.
ADC/DAC References
Address the reference through the setup register, bits 3
and 2. See Table 5. Following a wake-up delay, set
REFSEL[1:0] = 00 to program both the ADC and DAC
for internal reference use. Set REFSEL[1:0] = 10 to pro-
gram the ADC for internal reference use without a
wake-up delay. Set REFSEL[1:0] = 10 to program the
DAC for external reference, REF1. When using REF1 or
REF2/AIN_ in external-reference mode, connect a 0.1F
capacitor to AGND. Set REFSEL[1:0] = 01 to program
the ADC and DAC for external-reference mode. The
DAC uses REF1 as its external reference, while the
ADC uses REF2 as its external reference. Set
REFSEL[1:0] = 11 to program the ADC for external dif-
ferential reference mode. REF1 is the positive reference
and REF2 is the negative reference in the ADC external
differential mode.
When REFSEL[1:0] = 00 or 10, REF2/AIN_ functions as
an analog input channel. When REFSEL[1:0] = 01 or 11,
REF2/AIN_ functions as the device’s negative reference.
Temperature Measurements
Issue a command byte setting bit 0 of the conversion
register to one to take a temperature measurement.
See Table 4. The MAX1221/MAX1223/MAX1343 perform
temperature measurements with an internal diode-con-
nected transistor. The diode bias current changes from
68A to 4A to produce a temperature-dependent bias
voltage difference. The second conversion result at 4A
is subtracted from the first at 68A to calculate a digital
value that is proportional to absolute temperature. The
output data appearing at DOUT is the digital code
above, minus an offset to adjust from Kelvin to Celsius.
The reference voltage used for the temperature mea-
surements is always derived from the internal reference
source to ensure that 1 LSB corresponds to 1/8 of a
degree Celsius. On every scan where a temperature
measurement is requested, the temperature conversion
is carried out first. The first 2 bytes of data read from
the FIFO contain the result of the temperature measure-
ment. If another temperature measurement is per-
formed before the first temperature result is read out,
the old measurement is overwritten by the new result.
Temperature results are in degrees Celsius (two’s com-
plement). See the
Applications Information section for
information on how to perform temperature measure-
ments in each clock mode.
Register Descriptions
The MAX1221/MAX1223/MAX1343 communicate
between the internal registers and the external circuitry
through the SPI-compatible serial interface. Table 1
details the command byte, the registers, and the bit
names. Tables 4–12 show the various functions within
the conversion register, setup register, unipolar-mode
register, bipolar-mode register, ADC averaging regis-
ter, DAC select register, reset register, and GPIO com-
mand register, respectively.
Conversion Register
Select active analog input channels, scan modes, and
a single temperature measurement per scan by issuing
a command byte to the conversion register. Table 4
details channel selection, the four scan modes, and
how to request a temperature measurement. Start a
scan by writing to the conversion register when in clock
mode 10 or 11, or by applying a low pulse to the
CNVST pin when in clock mode 00 or 01. See Figures 6
and 7 for timing specifications for starting a scan with
CNVST.
A conversion is not performed if it is requested on a
channel or one of the channel pairs that has been con-
figured as
CNVST or REF2. For channels configured as
differential pairs, the CHSEL0 bit is ignored and the two
pins are treated as a single differential channel. For the
MAX1221/MAX1343, the CHSEL3 bit must be zero.
MAX1221/MAX1343
CURRENT
GPIOA0, GPIOA1
(mA)
GPIOC0, GPIOC1
(mA)
Sink
15
4
Source
15
2
Table 3. GPIO Maximum Sink/Source
Current
相關PDF資料
PDF描述
MAX188DCWP+ IC DAS 8CH 12BIT T/H LP 20-SOIC
MAX1407CAI+ IC DAS 16BIT LP 28-SSOP
MAX1414CAI+ IC DAS 16BIT LP 28-SSOP
NBXDPA019LN1TAG IC CLK XO LVDS 125/250MHZ 6CLCC
MAX181CCQH+D IC DAS 12BIT 100KSPS 44-PLCC
相關代理商/技術參數
參數描述
MAX1221BETX+ 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1221BETX+T 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1221BETX-T 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1223BETX 制造商:Maxim Integrated Products 功能描述:12-BIT MULTICHANNEL ADC/DAC WITH F - Rail/Tube
MAX1223BETX+ 制造商:Maxim Integrated Products 功能描述:12-BIT, MULTICHANNEL ADCS/DACS WITH FIFO, TEMPERATURE SENSIN - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC ADC 12BIT QFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*