- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1202 (Maxim Integrated Products, Inc.) Scan Test Devices With 18-Bit Bus Transceivers 56-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MAX1202 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Scan Test Devices With 18-Bit Bus Transceivers 56-SSOP -40 to 85 |
| 中文描述： | 5V、8通道、串行、12位ADC，3V數字接口 |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 309K |
| 代理商： | MAX1202 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
M
5V, 8-Channel, S erial, 12-Bit ADCs
with 3V Digital Interfac e
16
______________________________________________________________________________________
Figure 11a shows the serial-interface timing necessary
to perform a conversion every 15 SCLK cycles in exter-
nal clock mode. If
CS
is low and SCLK is continuous,
guarantee a start bit by first clocking in 16 zeros.
Most microcontrollers (μCs) require that data transfers
occur in multiples of eight clock cycles; 16 clocks per
conversion is typically the fastest that a μC can drive
the MAX1202/MAX1203. Figure 11b shows the
serial-interface timing necessary to perform a conver-
sion every 16 SCLK cycles in external clock mode.
__________ Applic ations Information
Power-On Reset
When power is first applied and if
SHDN
is not pulled
low, internal power-on reset circuitry activates the
MAX1202/MAX1203 in internal clock mode, ready to
convert with SSTRB = high. After the power supplies
are stabilized, the internal reset time is 100μs. No con-
versions should be performed during this phase.
SSTRB is high on power-up, and if
CS
is low, the first
logical 1 on DIN is interpreted as a start bit. Until a con-
version takes place, DOUT shifts out zeros.
Referenc e-Buffer Compensation
In addition to its shutdown function,
SHDN
also selects
internal or external compensation. The compensation
affects both power-up time and maximum conversion
speed. Compensated or not, the minimum clock rate is
100kHz due to droop on the sample-and-hold.
Float
SHDN
to select external compensation. The
Typical Operating Circuituses a 4.7μF capacitor at REF.
A value of 4.7μF or greater ensures stability and allows
converter operation at the 2MHz full clock speed.
External compensation increases power-up time (see
the section Choosing Power-Down Mode, and Table 5).
Internal compensation requires no external capacitor at
REF, and is selected by pulling
SHDN
high. Internal
compensation allows for the shortest power-up times,
but the external clock must be limited to 400kHz during
the conversion.
Power-Down
Choosing Power-Down Mode
You can save power by placing the converter in a low-
current shutdown state between conversions. Select full
power-down or fast power-down mode via bits 1 and 0
of the DIN control byte with
SHDN
high or floating
(Tables 2 and 6). Pull
SHDN
low at any time to shut
down the converter completely.
SHDN
overrides bits 1
and 0 of the control byte.
Full power-down mode turns off all chip functions that draw
quiescent current, reducing I
DD
and I
SS
typically to 2μA.
For the MAX1202, fast power-down mode turns off all
circuitry except the bandgap reference. With fast
power-down mode, the supply current is 30μA. Power-up
time can be shortened to 5μs in internal compensation
mode.
Since the MAX1203 does not have an internal reference,
power-up times coming out of full or fast power-down are
identical.
I
DD
shutdown current can increase if any digital input
(DIN, SCLK,
CS
) is held high in either power-down
mode. The actual shutdown current depends on the
state of the digital inputs, the voltage applied to the digi-
tal inputs (V
IH
), the supply voltage (V
DD
), and the operat-
ing temperature. Figure 12c shows the maximum I
DD
increase for each digital input held high in power-down
mode for different operating conditions. This current is
cumulative, so if all three digital inputs are held high, the
additional shutdown current is three times the value
shown in Figure 12c.
In both software power-down modes, the serial interface
remains operational, but the ADC does not convert.
Table 5 shows how the choice of reference-buffer com-
pensation and power-down mode affects both power-up
delay and maximum sample rate. In external compensa-
tion mode, power-up time is 20ms with a 4.7μF compen-
sation capacitor (200ms with a 33μF capacitor) when the
capacitor is initially fully discharged. From fast
power-down, start-up time can be eliminated by using
low-leakage capacitors that do not discharge more than
1/2LSB while shut down. In power-down, the capacitor
has to supply the current into the reference (typically
1.5μA) and the transient currents at power-up.
Figures 12a and 12b show the various power-down
sequences in both external and internal clock modes.
Software Power-Down
Software power-down is activated using bits PD1 and
PD0 of the control byte. As shown in Table 6, PD1 and
PD0 also specify the clock mode. When software
power-down is asserted, the ADC continues to operate
in the last specified clock mode until the conversion is
complete. The ADC then powers down into a low quies-
cent-current state. In internal clock mode, the interface
remains active and conversion results can be clocked
out even though the MAX1202/MAX1203 have already
entered software power-down.
The first logical 1 on DIN is interpreted as a start bit and
powers up the MAX1202/MAX1203. Following the start
bit, the control byte also determines clock and
power-down modes. For example, if the DIN word con-
tains PD1 = 1, the chip remains powered up. If PD1 = 0,
power-down resumes after one conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1202AEAP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1202BCPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1202ACPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203ACPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
| MAX1203BCPP | 5v, 8-cHANNEL, sERIAL, 12-bIT adcS WITH 3v dIGITAL iNTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1202ACAP | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202ACAP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202ACAP+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202ACAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202ACPP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。