- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1200AEMH (MAXIM INTEGRATED PRODUCTS INC) +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc PDF資料下載
參數資料
| 型號： | MAX1200AEMH |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| 中文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP44 |
| 封裝： | M0-108AA-2, MQFP-44 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 204K |
| 代理商： | MAX1200AEMH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
M
+5V S ingle-S upply, 1Msps, 16-Bit
S elf-Calibrating ADC
______________________________________________________________________________________
11
Calibration Proc edure
Since the MAX1200 is based on a pipelined architec-
ture, low-resolution quantizers (“coarse ADCs”) are
used to approximate the input signal. MDACs of the
same resolution are then used to reconstruct the input
signal, which is subtracted from the input and the
residue amplified by the SC gain stage. This residue is
then passed on to the next stage.
The accuracy of the MAX1200 is limited by the preci-
sion of the MDAC, which is strongly dependent on the
matching of the capacitors used. The mismatch
between the capacitors is determined and stored in an
on-chip memory, which is later used during the conver-
sion of the input signal.
During the calibration procedure, the clock must be
running continuously. ST_CAL (start of calibration) is
initiated by a positive pulse with a minimum width of
four clock cycles, but not longer than about 17,400
clock cycles (Figure 8).
The ST_CAL input may be asynchronous with the clock,
since it is retimed internally. With ST_CAL activated,
END_CAL goes low one or two clock cycles later and
remains low until the calibration is complete. During this
period, the reference voltages must be stable to less
than 0.01%; otherwise the calibration will be invalid.
During calibration, the analog inputs INP and INN are
not used; however, better performance is achieved if
these inputs are static. Once END_CAL goes high (indi-
cating that the calibration procedure is complete), the
ADC is ready for conversion.
changes (±5%) in power-supply voltage or tempera-
ture. Following calibration, if the temperature changes
more than ±20°C, the device should be recalibrated to
maintain optimum performance.
T wo’s Complement Output
The MAX1200 outputs data in two’s complement for-
mat. Table 1 shows how to convert the various full-
scale inputs into their two’s complement output codes.
Applic ations Information
S ignal-to-Noise Ratio (S NR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
full-scale analog input (RMS value) to the RMS quanti-
zation error (residual error). The ideal, theoretical mini-
mum analog-to-digital noise is caused by quantization
error only and results directly from the ADC’s resolution
(N bits):
SNR
(MAX)
= (6.02
·
N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is computed by taking
the ratio of the RMS signal to the RMS noise which
includes all spectral components minus the fundamen-
tal, the first nine harmonics, and the DC offset.
t
S
t
CH
t
CL
N
CLK
AIN
SAMPLE
CLOCK
DAV
N-3
N-2
N-1
N
N+1
D0–D15
N+1
N+2
N+3
N+4
N+5
t
OD
CLK
ST_CAL
END_CAL
MIN 4 t
CLK
~17,400 CLK CYCLES
Figure 8. Timing for Start and End of Calibration
Figure 7. Main Timing Diagram
Z
Z = HIGH IMPEDANCE (THREE-STATED)
Z
DOR
D0–D15
OE
t
AC
t
REL
Figure 9. Timing for Bus Access and Bus Relinquish—
Controlled by Output Enable (OE)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1200BCMH | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200ACMH | RB Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 24V; Output Voltage (Vdc): 05V; Power: 1W; Low Cost 1W Converter; Power Sharing on Dual Output Version; Industry Standard Pinout; 1kVDC & 2kVDC Isolation Options; Optional Continuous Short Circuit Protected; UL94V-0 Package Material; Efficiency to 85% |
| MAX1200BEMH | CANMS3120E20-41PF0 |
| MAX1201 | Scan Test Devices With 18-Bit Bus Transceivers 56-TSSOP -40 to 85 |
| MAX1201CMH | +5v sINGLE-sUPPLY, 2.2mSPS, 14-bIT sELF-cALIBRATING adc |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1200BCMH | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1200EVKIT-MQFP | 功能描述:數據轉換 IC 開發工具 Evaluation Kit for the MAX1200 MAX1201 MAX1205 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1201 | 制造商:Technical Pro 功能描述:Passive Two Way Molded ABS 12" PA/DJ Speaker - 1000W Max 制造商:TECHNICAL PRO 功能描述:DWO PA/DJ PROFESSIONAL SPEAKERTWO WAY 12 INCH 1000W MAX |
| MAX1202ACAP | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1202ACAP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。