- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1200 (Maxim Integrated Products, Inc.) +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc PDF資料下載
參數資料
| 型號： | MAX1200 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| 中文描述： | +5V單電源、1Msps、16位自校準ADC |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 204K |
| 代理商： | MAX1200 |
M
+5V S ingle-S upply, 1Msps, 16-Bit
S elf-Calibrating ADC
______________________________________________________________________________________
11
Calibration Proc edure
Since the MAX1200 is based on a pipelined architec-
ture, low-resolution quantizers (“coarse ADCs”) are
used to approximate the input signal. MDACs of the
same resolution are then used to reconstruct the input
signal, which is subtracted from the input and the
residue amplified by the SC gain stage. This residue is
then passed on to the next stage.
The accuracy of the MAX1200 is limited by the preci-
sion of the MDAC, which is strongly dependent on the
matching of the capacitors used. The mismatch
between the capacitors is determined and stored in an
on-chip memory, which is later used during the conver-
sion of the input signal.
During the calibration procedure, the clock must be
running continuously. ST_CAL (start of calibration) is
initiated by a positive pulse with a minimum width of
four clock cycles, but not longer than about 17,400
clock cycles (Figure 8).
The ST_CAL input may be asynchronous with the clock,
since it is retimed internally. With ST_CAL activated,
END_CAL goes low one or two clock cycles later and
remains low until the calibration is complete. During this
period, the reference voltages must be stable to less
than 0.01%; otherwise the calibration will be invalid.
During calibration, the analog inputs INP and INN are
not used; however, better performance is achieved if
these inputs are static. Once END_CAL goes high (indi-
cating that the calibration procedure is complete), the
ADC is ready for conversion.
Once calibrated, the MAX1200 is insensitive to small
changes (±5%) in power-supply voltage or tempera-
ture. Following calibration, if the temperature changes
more than ±20°C, the device should be recalibrated to
maintain optimum performance.
T wo’s Complement Output
The MAX1200 outputs data in two’s complement for-
mat. Table 1 shows how to convert the various full-
scale inputs into their two’s complement output codes.
Applic ations Information
S ignal-to-Noise Ratio (S NR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
full-scale analog input (RMS value) to the RMS quanti-
zation error (residual error). The ideal, theoretical mini-
mum analog-to-digital noise is caused by quantization
error only and results directly from the ADC’s resolution
(N bits):
SNR
(MAX)
= (6.02
·
N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is computed by taking
the ratio of the RMS signal to the RMS noise which
includes all spectral components minus the fundamen-
tal, the first nine harmonics, and the DC offset.
t
S
t
CH
t
CL
N
CLK
AIN
SAMPLE
CLOCK
DAV
N-3
N-2
N-1
N
N+1
D0–D15
N+1
N+2
N+3
N+4
N+5
t
OD
CLK
ST_CAL
END_CAL
MIN 4 t
CLK
~17,400 CLK CYCLES
Figure 8. Timing for Start and End of Calibration
Figure 7. Main Timing Diagram
Z
Z = HIGH IMPEDANCE (THREE-STATED)
Z
DOR
D0–D15
OE
t
AC
t
REL
Figure 9. Timing for Bus Access and Bus Relinquish—
Controlled by Output Enable (OE)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1200AEMH | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200BCMH | +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc |
| MAX1200ACMH | RB Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 24V; Output Voltage (Vdc): 05V; Power: 1W; Low Cost 1W Converter; Power Sharing on Dual Output Version; Industry Standard Pinout; 1kVDC & 2kVDC Isolation Options; Optional Continuous Short Circuit Protected; UL94V-0 Package Material; Efficiency to 85% |
| MAX1200BEMH | CANMS3120E20-41PF0 |
| MAX1201 | Scan Test Devices With 18-Bit Bus Transceivers 56-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX12000ETB+ | 制造商:Maxim Integrated Products 功能描述:1575MHZ GPS FRONT-END AMPLIFIER - Rail/Tube |
| MAX12000ETB+T | 功能描述:射頻放大器 1575MHz GPS Front End Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX12001ETB | 制造商:Maxim Integrated Products 功能描述: |
| MAX12001ETB+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX12001ETB+T | 功能描述:射頻放大器 1575MHz GPS LNA RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。