mid supply (V
參數資料
型號： MAX1198ECM+D
廠商： Maxim Integrated Products
文件頁數： 5/22頁
文件大?。?/td> 0K
描述： IC ADC 8BIT 100MSPS DUAL 48-TQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 250
位數： 8
采樣率（每秒）： 100M
數據接口： 并聯
轉換器數目： 2
功率耗散（最大）： 314mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP 裸露焊盤
供應商設備封裝： 48-TQFP 裸露焊盤（7x7）
包裝： 托盤
輸入數目和類型： 4 個單端，雙極；2 個差分，雙極
產品目錄頁面： 1396 (CN2011-ZH PDF)
Match the impedance of INA+ and INA-, as well as
INB+ and INB-, and set the common-mode voltage to
mid supply (VDD/2) for optimum performance.
Analog Inputs and Reference
Configurations
The full-scale range of the MAX1198 is determined by
the internally generated voltage difference between
REFP (VDD/2 + VREFIN/4) and REFN (VDD/2 - VREFIN/4).
The full-scale range for both on-chip ADCs is
adjustable through the REFIN pin, which is provided for
this purpose.
The MAX1198 provides three modes of reference operation:
Internal reference mode
Buffered external reference mode
Unbuffered external reference mode
In internal reference mode, connect the internal refer-
ence output REFOUT to REFIN through a resistor (e.g.,
10k
) or resistor-divider, if an application requires a
reduced full-scale range. For stability and noise-filtering
purposes, bypass REFIN with a >10nF capacitor to
GND. In internal reference mode, REFOUT, COM,
REFP, and REFN become low-impedance outputs.
In buffered external reference mode, adjust the refer-
ence voltage levels externally by applying a stable and
accurate voltage at REFIN. In this mode, COM, REFP,
and REFN are outputs. REFOUT can be left open or
connected to REFIN through a >10k
resistor.
In unbuffered external reference mode, connect REFIN
to GND. This deactivates the on-chip reference buffers
for REFP, COM, and REFN. With their buffers shut
down, these nodes become high-impedance inputs
and can be driven through separate, external reference
sources.
For detailed circuit suggestions and how to drive this
dual ADC in buffered/unbuffered external reference
mode, see the Applications Information section.
Clock Input (CLK)
The MAX1198’s CLK input accepts a CMOS-compati-
ble clock signal. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low
jitter and fast rise and fall times (<2ns). In particular,
sampling occurs on the rising edge of the clock signal,
requiring this edge to provide lowest possible jitter. Any
significant aperture jitter would limit the SNR perfor-
mance of the on-chip ADCs as follows:
where fIN represents the analog input frequency and
tAJ is the time of the aperture jitter.
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines.
SNR
ft
IN
AJ
log
=×
××
×
20
1
2
π
MAX1198
Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
13
N - 6
N
N - 5
N + 1
N - 4
N + 2
N - 3
N + 3
N - 2
N + 4
N - 1
N + 5
N
N + 6
N + 1
5-CLOCK-CYCLE LATENCY
ANALOG INPUT
CLOCK INPUT
DATA OUTPUT
D7A–D0A
tDO
tCH
tCL
N - 6
N - 5
N - 4
N - 3
N - 2
N - 1
N
N + 1
DATA OUTPUT
D7B–D0B
tAD
Figure 3. System Timing Diagram
相關PDF資料
PDF描述
VI-BTL-MX-F4 CONVERTER MOD DC/DC 28V 75W
MAX1304ECM+ IC ADC 12BIT 8CH 4MSPS 48LQFP
VI-BTL-MX-F3 CONVERTER MOD DC/DC 28V 75W
MAX1297ACEG+ IC ADC 12BIT 265KSPS 24-QSOP
VI-BTL-MX-F1 CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
MAX1198ECM-TD 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1198EVKIT 功能描述:數據轉換 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX11G 制造商:Aavid Thermalloy 功能描述:METALIC HEAT SINK CLIP
MAX11NG 功能描述:散熱片 MaxClip TO220/Max220 9lb 24.7x12mm RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR
MAX12 制造商:Aavid Thermalloy 功能描述:CBL ACC LOW FORCE CLIP - Bulk 制造商:Lanzar 功能描述:4Ohm 1000W Peak 12 Paper Cone Woofer 制造商:LANZAR 功能描述:12 PAPER CONE WOOFER 4OHM 1000W PEAK 制造商:Aavid Thermalloy 功能描述:Thrml Mgmt Access Heat Sink Clip
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*