參數資料
型號： MAX1190ECM
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： ADC
英文描述： Dual 10-Bit, 120Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs
中文描述： DUAL 1-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQFP48
封裝： 7 X 7 MM, 1.0 MM HEIGHT, MS-026ABA-HD, TQFP-48
文件頁數： 19/21頁
文件大?。?/td> 739K
代理商： MAX1190ECM
highest level of signal integrity. Consider the use of a split
ground plane arranged to match the physical location of
the analog ground (GND) and the digital output driver
ground (OGND) on the ADC
’
s package. The two ground
planes should be joined at a single point such that the
noisy digital ground currents do not interfere with the ana-
log ground plane. The ideal location of this connection
can be determined experimentally at a point along the
gap between the two ground planes, which produces
optimum results. Make this connection with a low-value,
surface-mount resistor (1
to 5
), a ferrite bead, or a
direct short. Alternatively, all ground pins could share the
same ground plane if the ground plane is sufficiently iso-
lated from any noisy, digital systems ground plane (e.g.,
downstream output buffer or DSP ground plane). Route
high-speed digital signal traces away from the sensitive
analog traces of either channel. Make sure to isolate the
analog input lines to each respective converter to mini-
mize channel-to-channel crosstalk. Keep all signal lines
short and free of 90
°
turns.
Static Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. This straight
line can be either a best-straight-line fit or a line drawn
between the endpoints of the transfer function, once off-
set and gain errors have been nullified. The static linearity
parameters for the MAX1190 are measured using the
best-straight-line fit method.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an actu-
al step width and the ideal value of 1LSB. A DNL error
specification of less than 1LSB guarantees no missing
codes and a monotonic transfer function.
Dynamic Parameter Definitions
Aperture Jitter
Figure 11 depicts the aperture jitter (t
AJ
), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (t
AD
) is the time defined between the
falling edge of the sampling clock and the instant when
an actual sample is taken (Figure 11).
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC
’
s reso-
lution (N bits):
SNR
dB[max]
= 6.02
dB
N + 1.76
dB
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise, which includes all spectral
components minus the fundamental, the first five har-
monics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to all spectral components minus the fundamental
and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at a
specific input frequency and sampling rate. An ideal
ADC
’
s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed from:
ENOB
SINAD
=
1 76
.
6 02
.
M
Dual 10-Bit, 120Msps, 3.3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
19
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
t
AD
t
AJ
TRACK
TRACK
CLK
Figure 11. T/H Aperture Timing
相關PDF資料
PDF描述
MAX1191 Ultra-Low-Power, 7.5Msps, Dual 8-Bit ADC
MAX1191ETI-T Ultra-Low-Power, 7.5Msps, Dual 8-Bit ADC
MAX1198 Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs
MAX1198ECM Dual, 8-Bit, 100Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs
MAX1200 +5v sINGLE-sUPPLY, 1mSPS, 16-bIT sELF-cALIBRATING adc
相關代理商/技術參數
參數描述
MAX1190ECM+ 制造商:Maxim Integrated Products 功能描述:IC SM ADC LOW POWER 10-BIT DUAL
MAX1190ECM+D 功能描述:模數轉換器 - ADC 10Bit 2Ch 120Msps 3.3V Low-Power ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1190ECM+TD 功能描述:模數轉換器 - ADC 10Bit 2Ch 120Msps 3.3V Low-Power ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1190ECM-D 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1190ECM-TD 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*