參數資料
型號： MAX1182ECM+TD
廠商： Maxim Integrated Products
文件頁數： 5/21頁
文件大?。?/td> 0K
描述： IC ADC 10BIT 65MSPS DL 48-TQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,000
位數： 10
采樣率（每秒）： 65M
數據接口： 并聯
轉換器數目： 2
功率耗散（最大）： 240mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP 裸露焊盤
供應商設備封裝： 48-TQFP 裸露焊盤（7x7）
包裝： 帶卷 (TR)
輸入數目和類型： 4 個單端，雙極；2 個差分，雙極
MAX1182
Dual 10-Bit, 65Msps, 3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
13
Analog Inputs and Reference
Configurations
The full-scale range of the MAX1182 is determined by the
internally generated voltage difference between REFP
(VDD / 2 + VREFIN / 4) and REFN (VDD / 2 - VREFIN / 4).
The full-scale range for both on-chip ADCs is adjustable
through the REFIN pin, which is provided for this purpose.
REFOUT, REFP, COM (VDD / 2), and REFN are internal-
ly buffered low-impedance outputs.
The MAX1182 provides three modes of reference oper-
ation:
Internal reference mode
Buffered external reference mode
Unbuffered external reference mode
In internal reference mode, connect the internal refer-
ence output REFOUT to REFIN through a resistor (e.g.,
10k
Ω) or resistor divider, if an application requires a
reduced full-scale range. For stability and noise filtering
purposes bypass REFIN with a > 10nF capacitor to
GND. In internal reference mode, REFOUT, COM,
REFP, and REFN become low-impedance outputs.
In buffered external reference mode, adjust the refer-
ence voltage levels externally by applying a stable and
accurate voltage at REFIN. In this mode, COM, REFP,
and REFN become outputs. REFOUT may be left open
or connected to REFIN through a > 10k
Ω resistor.
In unbuffered external reference mode, connect REFIN
to GND. This deactivates the on-chip reference buffers
for REFP, COM, and REFN. With their buffers shut
down, these nodes become high impedance and may
be driven through separate external reference sources.
Clock Input (CLK)
The MAX1182’s CLK input accepts CMOS-compatible
clock signals. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low
jitter and fast rise and fall times (< 2ns). In particular,
sampling occurs on the rising edge of the clock signal,
requiring this edge to provide lowest possible jitter. Any
significant aperture jitter would limit the SNR perfor-
mance of the on-chip ADCs as follows:
SNRdB = 20 log10 (1 / [2
π x fIN x tAJ]),
where fIN represents the analog input frequency and tAJ
is the time of the aperture jitter.
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines.
The MAX1182 clock input operates with a voltage thresh-
old set to VDD / 2. Clock inputs with a duty cycle other
than 50%, must meet the specifications for high and low
periods as stated in the Electrical Characteristics.
System Timing Requirements
Figure 3 depicts the relationship between the clock
input, analog input, and data output. The MAX1182
samples at the rising edge of the input clock. Output
data for channels A and B is valid on the next rising
edge of the input clock. The output data has an internal
latency of five clock cycles. Figure 4 also determines
the relationship between the input clock parameters
and the valid output data on channels A and B.
Digital Output Data, Output Data Format
Selection (T/B), Output Enable (/OE)
All digital outputs, D0A–D9A (Channel A) and D0B–D9B
(Channel B), are TTL/CMOS logic-compatible. There is
a 5-clock-cycle latency between any particular sample
and its corresponding output data. The output coding
can be chosen to be either straight offset binary or
two’s complement (Table 1) controlled by a single pin
(T/B). Pull T/B low to select offset binary and high to
activate two’s complement output coding. The capaci-
tive load on the digital outputs D0A–D9A and D0B–D9B
should be kept as low as possible (< 15pF), to avoid
large digital currents that could feed back into the ana-
log portion of the MAX1182, thereby degrading its
dynamic performance. Using buffers on the digital out-
puts of the ADCs can further isolate the digital outputs
from heavy capacitive loads. To further improve the
dynamic performance of the MAX1182 small-series
resistors (e.g., 100
Ω) maybe added to the digital output
paths, close to the MAX1182.
Figure 4 displays the timing relationship between out-
put enable and data output valid as well as power
down/wake-up and data output valid.
Power-Down (PD) and
Sleep (SLEEP) Modes
The MAX1182 offers two power-save modes—sleep and
full power-down mode. In sleep mode (SLEEP = 1), only
the reference bias circuit is active (both ADCs are dis-
abled), and current consumption is reduced to 2.8mA.
To enter full power-down mode, pull PD high. With OE
simultaneously low, all outputs are latched at the last
value prior to the power down. Pulling OE high forces
the digital outputs into a high impedance state.
相關PDF資料
PDF描述
MAX1185ECM+D IC ADC 10BIT 20MSPS DUAL 48-TQFP
MAX1188AEUP+ IC ADC 16BIT 135KSPS 20-TSSOP
MAX1193ETI+ IC ADC 8BIT 45MSPS DUAL 28-TQFN
MAX1196ECM+TD IC ADC 8BIT 40MSPS DL 48-TQFP
MAX1198ECM+TD IC ADC 8BIT 100MSPS DL 48-TQFP
相關代理商/技術參數
參數描述
MAX11835DEMOKIT+ 功能描述:數據轉換 IC 開發工具 Demonstration Kit for MAX11835 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX11835EWA+ 制造商:Maxim Integrated Products 功能描述:
MAX11835EWA+T 功能描述:觸摸屏轉換器和控制器 TacTouch Haptic Actuator Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11835TEVS+ 功能描述:觸摸屏轉換器和控制器 Evaluation System for MAX11835 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11836EWA+T 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:DUAL 10-BIT 40MSPS 3V LOW-POWER ADC WITH INTERNAL REFER - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*