- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1182 (Maxim Integrated Products, Inc.) Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs PDF資料下載
參數資料
| 型號： | MAX1182 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| 中文描述： | 雙路、10位、65Msps、+3V、低功耗ADC，內置電壓基準，并行輸出 |
| 文件頁數： | 13/22頁 |
| 文件大?。?/td> | 684K |
| 代理商： | MAX1182 |
M
Dual 10-Bit, 65Msps, +3V, Low-Power ADC with
Internal Reference and Parallel Outputs
______________________________________________________________________________________
13
Analog Inputs and Reference
Configurations
The full-scale range of the MAX1182 is determined by the
internally generated voltage difference between REFP
(V
DD
/2 + V
REFIN
/4) and REFN (V
DD
/2 - V
REFIN
/4). The
full-scale range for both on-chip ADCs is adjustable
through the REFIN pin, which is provided for this purpose.
REFOUT, REFP, COM (VDD/2), and REFN are internally
buffered low-impedance outputs.
The MAX1182 provides three modes of reference oper-
ation:
Internal reference mode
Buffered external reference mode
Unbuffered external reference mode
In internal reference mode, connect the internal refer-
ence output REFOUT to REFIN through a resistor (e.g.,
10k
) or resistor divider, if an application requires a
reduced full-scale range. For stability and noise filtering
purposes bypass REFIN with a >10nF capacitor to
GND. In internal reference mode, REFOUT, COM,
REFP, and REFN become low-impedance outputs.
In buffered external reference mode, adjust the refer-
ence voltage levels externally by applying a stable and
accurate voltage at REFIN. In this mode, COM, REFP,
and REFN become outputs. REFOUT may be left open
or connected to REFIN through a >10k
resistor.
In unbuffered external reference mode, connect REFIN
to GND. This deactivates the on-chip reference buffers
for REFP, COM, and REFN. With their buffers shut
down, these nodes become high impedance and may
be driven through separate external reference sources.
Clock Input (CLK)
The MAX1182
’
s CLK input accepts CMOS-compatible
clock signals. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low
jitter and fast rise and fall times (< 2ns). In particular,
sampling occurs on the rising edge of the clock signal,
requiring this edge to provide lowest possible jitter. Any
significant aperture jitter would limit the SNR perfor-
mance of the on-chip ADCs as follows:
SNR
dB
= 20
log
10
(1 / [2
π
x f
IN
x t
AJ
]),
where f
IN
represents the analog input frequency and t
AJ
is the time of the aperture jitter.
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines.
The MAX1182 clock input operates with a voltage thresh-
old set to V
DD
/2. Clock inputs with a duty cycle other than
50%, must meet the specifications for high and low peri-
ods as stated in the
Electrical Characteristics
.
System Timing Requirements
Figure 3 depicts the relationship between the clock
input, analog input, and data output. The MAX1182
samples at the rising edge of the input clock. Output
data for channels A and B is valid on the next rising
edge of the input clock. The output data has an internal
latency of five clock cycles. Figure 4 also determines
the relationship between the input clock parameters
and the valid output data on channels A and B.
Digital Output Data, Output Data Format
Selection (T/B), Output Enable (/OE)
All digital outputs, D0A
–
D9A (Channel A) and D0B
–
D9B
(Channel B), are TTL/CMOS logic-compatible. There is
a 5-clock-cycle latency between any particular sample
and its corresponding output data. The output coding
can be chosen to be either straight offset binary or
two
’
s complement (Table 1) controlled by a single pin
(T/B). Pull T/B low to select offset binary and high to
activate two
’
s complement output coding. The capaci-
tive load on the digital outputs D0A
–
D9A and D0B
–
D9B
should be kept as low as possible (<15pF), to avoid
large digital currents that could feed back into the ana-
log portion of the MAX1182, thereby degrading its
dynamic performance. Using buffers on the digital out-
puts of the ADCs can further isolate the digital outputs
from heavy capacitive loads. To further improve the
dynamic performance of the MAX1182 small-series
resistors (e.g., 100
) maybe added to the digital output
paths, close to the MAX1182.
Figure 4 displays the timing relationship between out-
put enable and data output valid as well as power
down/wake-up and data output valid.
Power-Down (PD) and
Sleep (SLEEP) Modes
The MAX1182 offers two power-save modes
—
sleep and
full power-down mode. In sleep mode (SLEEP = 1), only
the reference bias circuit is active (both ADCs are dis-
abled), and current consumption is reduced to 2.8mA.
To enter full power-down mode, pull PD high. With
OE
simultaneously low, all outputs are latched at the last
value prior to the power down. Pulling
OE
high forces
the digital outputs into a high impedance state.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1183 | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183ECM | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1185 | Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs |
| MAX1185ECM | Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs |
| MAX1190 | Dual 10-Bit, 120Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1182ECM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1182ECM+D | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1182ECM+TD | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1182ECM-D | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1182ECM-T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。