Controllers with I2C/SP" />
參數資料
型號： MAX11801ETC/V+T
廠商： Maxim Integrated Products
文件頁數： 29/59頁
文件大?。?/td> 0K
描述： IC TOUCH SCREEN CTRLR LP 12WQFN
其它有關文件： Automotive Product Guide
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
類型： 電阻
觸摸面板接口： 4 線
輸入數/鍵： 1 TSC
分辨率（位）： 12 b
評估套件： 可供
數據接口： I²C，串行
數據速率/采樣率 (SPS，BPS)： 105k
電源電壓： 1.7 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 12-WQFN 裸露焊盤
供應商設備封裝： 12-TQFN-EP（4x4）
包裝： 帶卷 (TR)
MAX11800–MAX11803
Low-Power, Ultra-Small Resistive Touch-Screen
Controllers with I2C/SPI Interface
______________________________________________________________________________________
35
For example:
0000 = 2-1 LSB = aperture checking disabled
0001 = 2(1-1) LSB = ±1 LSB
0010 = 2(2-1) LSB = ±2 LSB
0011 = 2(3-1) LSB = ±4 LSB
…
1001 = 2(9-1) LSB = ±256 LSB (1/16 of the touch screen
in each direction)
1010 = 2(10-1) LSB = ±512 LSB (1/8 of the touch screen
in each direction)
1011 = 2(11-1) LSB = ±1024 LSB (1/4 of the touch
screen in each direction)
1100 = 2(12-1) LSB = ±2048 LSB (1/2 of the touch
screen in each direction)
1101 to 1111 = aperture checking disabled
FIFO Aperture Criteria
In autonomous mode with aperture engaged, new data
is written to the FIFO, and an interrupt is issued when
the following conditions occur (aperture mode is not
available in direct conversion mode).
New Panel Touch Initiated
The FIFO updates and issues an interrupt when a new
touch is observed on the panel (data tag = 00). This
event occurs regardless of the current aperture setting
and the previous touch location so that multiple presses
in the same location can be observed and registered.
Continuous Panel Touch Terminated
The FIFO updates and issues an interrupt when a con-
tinuous panel touch is terminated (data tag = 10). This
event occurs regardless of the current aperture setting
and the previous continuous touch location(s) so that
multiple presses in the same location can be observed
and registered.
Continuous Panel Touch
Measurement Meets Aperture Criteria
The MAX11800/MAX11801 log the measurement data
to the FIFO and issue an interrupt when a measurement
during a continuous panel touch (event tag = 01) meets
the aperture criteria (i.e., lies on or outside the aperture
boundary). This event occurs when the point of contact
is dragged across the touch screen. Only the
ΔX or ΔY
aperture criteria need to be met and a greater than or
equal to qualification criterion is applied. If the change
in X position or change in Y position exceeds the aper-
ture criteria, then an interrupt is generated.
Applications Information
Using Aperture Mode
Aperture mode is only supported in the MAX11800/
MAX11801. The MAX11800/MAX11801 accommodate
touch-panel applications where limited resolution in
both time and space can be traded off for reduced
microprocessor activity. A simulated keypad is an
example of an application where autonomous conver-
sion mode with aperture checking could yield an effi-
cient solution.
The AP determines the durations of touch-screen
presses. An issuance of TIRQ interrupts accompanies
all FIFO events. The interrupts clear when all existing
data is read back by the AP, allowing the AP to correct-
ly interpret held panel data.
The FIFO updates immediately when a new touch event
is detected. The system assumes that the panel touch is
continuous after the AP receives the interrupt. The
MAX11800/MAX11801 continue to scan the panel at the
user-programmed sample rate. The FIFO updates when
the measurement data shows that the panel touch loca-
tion moves (i.e., a measurement exceeds either of the
selected aperture ranges). The FIFO also updates upon
detection of a panel release. The AP determines the
duration of the press by observing the time between the
leading edge of the touch (tag 00) and the release edge
of the touch (tag 10). All midpress data (tag 01) are inter-
preted as part of a dragged touch event.
All valid touch events log two data points into the FIFO:
an initial data point at the beginning of the touch (tag
00) and a release data point at the termination of the
touch (tag 10). Discard release edge position data as
invalid as the MAX11800/MAX11801 cannot determine
at which point in the ADC conversion cycle the panel is
released during the measurement operation. If the
release occurs while the ADC is actively sampling the
panel, the results are invalid. Only initial and midpress
position data are reliable.
Any touch event too short in duration to log both initial
and release data points is recorded in the FIFO as a
release (tag 10) and discarded as a glitch event.
Measuring durations of panel touches becomes
impractical when the AP services the MAX11800/
MAX11801 at lower than the operating speed of the
devices and the panel combined. The AP cannot time
the duration between panel touches when both the ini-
tial and release data points can be logged before the
initial interrupt is serviced. Do not allow the FIFO to
overflow as touch information can be lost and the FIFO
content becomes invalid.
相關PDF資料
PDF描述
MS27474T22F35SD CONN RCPT 100POS JAM NUT W/SCKT
MAX11802ETC+T IC TOUCH SCREEN CTLR 12-TQFN
MS3120F20-41P CONN RCPT 41POS WALL MNT W/PINS
MAX11803ETC+T IC TOUCH SCREEN CTLR 12-TQFN
GTC01AF-20-7S CONN RCPT 8POS INLINE W/SCKT
相關代理商/技術參數
參數描述
MAX11801EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX11801 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX11801EWC+ 制造商:Maxim Integrated Products 功能描述:
MAX11801EWC+T 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801GTC/V+ 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
MAX11801GTC/V+T 功能描述:觸摸屏轉換器和控制器 I2C 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*