- 您現在的位置：買賣IC網 > PDF目錄9894 > MAX1174BCUP+ (Maxim Integrated Products)IC ADC 14BIT 135KSPS 20-TSSOP PDF資料下載
參數資料
| 型號： | MAX1174BCUP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 135KSPS 20-TSSOP |
| 標準包裝： | 74 |
| 位數： | 14 |
| 采樣率（每秒）： | 135k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 879mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極 |
MAX1156/MAX1158/MAX1174
External Reference
An external reference can be placed at either the input
(REFADJ) or the output (REF) of the MAX1156/
MAX1158/MAX1174’s internal buffer amplifier. Using
the buffered REFADJ input makes buffering the exter-
nal reference unnecessary. The input impedance of
REFADJ is typically 5k
. The internal buffer output
must be bypassed at REF with a 10F capacitor.
Connect REFADJ to AVDD to disable the internal buffer.
Directly drive REF using an external 3.8V to 4.2V refer-
ence. During conversion, the external reference must
be able to drive 100A of DC load current and have an
output impedance of 10
or less.
For optimal performance, buffer the reference through
an op amp and bypass REF with a 10F capacitor.
Consider the MAX1156/MAX1158/MAX1174’s equiva-
lent input noise (0.32LSB) when choosing a reference.
Reading the Conversion Result
EOC is provided to flag the microprocessor when a
conversion is complete. The falling edge of EOC sig-
nals that the data is valid and ready to be output to the
bus. D0–D13 are the parallel outputs of the
MAX1156/MAX1158/MAX1174. These three-state out-
puts allow for direct connection to a microcontroller I/O
bus. The outputs remain high-impedance during acqui-
sition and conversion. Data is loaded onto the output
bus with the third falling edge of CS with R/C high (after
tDO). Bringing CS high forces the output bus back to
high impedance. The MAX1156/MAX1158/MAX1174
then wait for the next falling edge of CS to start the next
conversion cycle (see Figure 2).
HBEN toggles the output between the high/low byte.
The low byte is loaded onto the output bus when HBEN
is low and the high byte is on the bus when HBEN is
high. The two MSBs of the high byte are always zero.
Transfer Function
Figures 8, 9, and 10 show the MAX1156/MAX1158/
MAX1174 output transfer functions. The MAX1158 and
MAX1174 outputs are coded in offset binary, while the
MAX1156 is coded in standard binary.
Input Buffer
Most applications require an input buffer amplifier to
achieve 14-bit accuracy and prevent loading the
source. Switch the channels immediately after acquisi-
tion, rather than near the end of or after a conversion,
when the input signal is multiplexed. This allows more
time for the input buffer amplifier to respond to a large
step-change in input signal. The input amplifier must
have a high enough slew rate to complete the required
output voltage change before the beginning of the
acquisition time. Figure 11 shows an example of this
circuit using the MAX427.
Figures 12a and 12b show how the MAX1158 and
MAX1174 analog input current varies depending on
whether the chip is operating or powered down. The
part is fully powered down between conversions if the
voltage at R/C is set high during the second falling
edge of CS. The input current abruptly steps to the
powered up value at the start of acquisition. This step
in the input current can disrupt the ADC input, depend-
ing on the driving circuit’s output impedance at high
frequencies. If the driving circuit cannot fully settle by
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
10
______________________________________________________________________________________
CS
R/C
EOC
REF AND
BUFFER
POWER
ACQUISITION
CONVERSION
DATA
OUT
Figure 5. Selecting Standby Mode
CS
R/C
EOC
REF AND
BUFFER
POWER
ACQUISITION
CONVERSION
DATA
OUT
Figure 6. Selecting Shutdown Mode
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1065BCUI+ | IC ADC 14BIT 165KSPS 28TSSOP |
| VE-2WD-MX-F2 | CONVERTER MOD DC/DC 85V 75W |
| MAX1003CAX+ | IC ADC 6BIT 90MSPS DL 36-SSOP |
| MAX1497EAI+ | IC ADC 3 1/2DIG W/LED DVR 28-SSO |
| MS3122E22-21S | CONN RCPT 21POS BOX MOUNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1174BCUP+ | 功能描述:模數轉換器 - ADC 14-Bit 135ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1174BCUP+T | 功能描述:模數轉換器 - ADC 14-Bit 135ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1174BCUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1174BEUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1174BEUP+ | 功能描述:模數轉換器 - ADC 14-Bit 135ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。