- 您現在的位置：買賣IC網 > PDF目錄10572 > MAX1110CAP+ (Maxim Integrated Products)IC ADC SRL 8CH8BIT 50KSPS 20SSOP PDF資料下載
參數資料
| 型號： | MAX1110CAP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/20頁 |
| 文件大小： | 0K |
| 描述： | IC ADC SRL 8CH8BIT 50KSPS 20SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 66 |
| 位數： | 8 |
| 采樣率（每秒）： | 50k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 889mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，雙極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
MAX1110/MAX1111
+2.7V, Low-Power, Multichannel,
Serial 8-Bit ADCs
10
______________________________________________________________________________________
Table 3. Control-Byte Format
START
SEL2
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
PD0
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(MSB)
(LSB)
NAME
SGL/DIF
2
BIT
1 = single ended, 0 = differential. Selects single-ended or differential conversions. In single-
ended mode, input signal voltages are referred to COM. In differential mode, the voltage differ-
ence between two channels is measured (Tables 1 and 2).
DESCRIPTION
UNI/BIP
3
START
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. Select differential operation
if bipolar mode is used (Table 4).
PD0
0 (LSB)
7 (MSB)
1 = external clock mode, 0 = internal clock mode.
Selects external or internal clock mode.
The first logic “1” bit after CS goes low defines the beginning of the control byte.
SEL2
SEL1
SEL0
6
5
4
Select which of the input channels are to be used for the conversion (Tables 1 and 2).
PD1
1
1 = fully operational, 0 = power-down.
Selects fully operational or power-down mode.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the minimum time needed for the signal to be
acquired. It is calculated by:
tACQ = 6 x (RS + RIN) x 18pF
where RIN = 6.5kΩ, RS = the source impedance of the
input signal, and tACQ is never less than 1s. Note that
source impedances below 2.4kΩ do not significantly
affect the AC performance of the ADC.
Input Bandwidth
The ADC’s input tracking circuitry has a 1.5MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. To avoid high-
frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Inputs
Internal protection diodes, which clamp the analog
input to VDD and AGND, allow the channel input pins to
swing from (AGND - 0.3V) to (VDD + 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed VDD by more than 50mV or
be lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over 2mA.
The MAX1110/MAX1111 can be configured for differen-
tial or single-ended inputs with bits 2 and 3 of the con-
trol byte (Table 3). In single-ended mode, the analog
inputs are internally referenced to COM with a full-scale
input range from COM to VREFIN + COM. For bipolar
operation, set COM to VREFIN/2.
In differential mode, choosing unipolar mode sets the
differential input range at 0V to VREFIN. In unipolar
mode, the output code is invalid (code zero) when a
negative differential input voltage is applied. Bipolar
mode sets the differential input range to ±VREFIN/2.
Note that in this mode, the common-mode input range
includes both supply rails. Refer to Table 4 for input
voltage ranges.
Quick Look
To quickly evaluate the MAX1110/MAX1111’s analog
performance, use the circuit of Figure 5. The
MAX1110/MAX1111 require a control byte to be written
to DIN before each conversion. Tying DIN to +3V feeds
相關PDF資料 |
PDF描述 |
|---|---|
| MS3102E22-6P | CONN RCPT 3POS BOX MNT W/PINS |
| VI-B5J-IV-F2 | CONVERTER MOD DC/DC 36V 150W |
| VE-BTK-MX-F2 | CONVERTER MOD DC/DC 40V 75W |
| A7FB | CONN PLUG CORD FMAL 7PIN BLK/SLV |
| AD7467BRTZ-R2 | IC ADC 10BIT 1.6V MCRPWR SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1110CAP+ | 功能描述:模數轉換器 - ADC 2.7V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1110CAP+T | 功能描述:模數轉換器 - ADC 2.7V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1110CAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1110CPP | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1110CPP+ | 功能描述:模數轉換器 - ADC 2.7V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。