- 您現在的位置：買賣IC網 > PDF目錄10572 > MAX1108EUB+ (Maxim Integrated Products)IC ADC 8BIT LP 10-UMAX PDF資料下載
參數資料
| 型號： | MAX1108EUB+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/20頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT LP 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 8 |
| 采樣率（每秒）： | 50k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 444mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個偽差分，單極；1 個偽差分，雙極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
MAX1108/MAX1109
External Reference
To use an external reference, set bit 2 (I/EREF) and bit
1 (REFSHDN) of control byte to 0 and connect the
external reference (VREF between 1V and VDD) directly
at the REF pin. The DC input impedance at REF is
extremely high, consisting of leakage current only (typi-
cally 10nA). During a conversion, the reference must
be able to deliver up to 20A average load current and
have an output impedance of 1k
or less at the conver-
sion clock frequency. If the reference has higher output
impedance or is noisy, bypass it close to the REF pin
with a 0.1F capacitor. MAX1109 has an internal refer-
ence of +4.096V. To use the device with supply volt-
ages below 4.5V, external reference mode is required.
With an external reference voltage of less than +2.048V
(MAX1108) or +4.096V (MAX1109) at REF, the increase
in the ratio of the RMS noise to the LSB value (FS / 256)
results in performance degradation and decreased
dynamic range.
Internal Reference
To use the internal reference, set bit 2 (I/EREF) and bit 1
(REFSHDN) of the control byte to 1 and bypass REF with
a 1F capacitor to ground. The internal reference can be
powered down after a conversion by setting bit 1 (REF-
SHDN) of the control byte to 0. When using the internal
reference, use MAX1108 and MAX1109 with supply volt-
age below 4.5V and above 4.5V, respectively.
Transfer Function
Table 4 shows the full-scale voltage ranges for unipolar
and bipolar modes. Figure 12a depicts the nominal,
unipolar I/O transfer function, and Figure 12b shows the
bipolar I/O transfer function. The zero scale is deter-
mined by the input selection setting and is either COM,
GND, or CH1.
Code transitions occur at integer LSB values. Output
coding is straight binary for unipolar operation and
two’s complement for bipolar operation. With a +2.048V
reference, 1LSB = 8mV (VREF / 256).
Layout, Grounding, and Bypassing
For best performance, use printed circuit boards. Wire-
wrap boards are not recommended. Board layout
should ensure that digital and analog signal lines are
separated from each other. Do not run analog and digi-
tal (especially clock) lines parallel to one another or run
digital lines underneath the ADC package.
Figure 13 shows the recommended system-ground
connections. A single-point analog ground (star-ground
point) should be established at the A/D ground.
Connect all analog grounds to the star ground. No digi-
tal-system ground should be connected to this point.
The ground return to the power supply for the star
ground should be low impedance and as short as pos-
sible for noise-free operation.
High-frequency noise in the VDD power supply may
affect the comparator in the ADC. Bypass the supply to
the star ground with 0.1F and 1F capacitors close to
the VDD pin of the MAX1108/MAX1109. Minimize
capacitor lead lengths for best supply-noise rejection. If
the power supply is very noisy, a 10
resistor can be
connected to form a lowpass filter.
Single-Supply, Low-Power,
2-Channel, Serial 8-Bit ADCs
18
______________________________________________________________________________________
OUTPUT CODE
FULL-SCALE
TRANSITION
11111111
11111110
11111101
00000011
00000010
00000001
00000000
12
3
0
FS
FS - 1LSB
FS = VREF + COM
1LSB = VREF
256
INPUT VOLTAGE (LSB)
(COM)
Figure 12a. Unipolar Transfer Function
01111111
OUTPUT CODE
01111110
00000010
00000001
00000000
11111111
11111110
11111101
10000001
10000000
-FS
COM
INPUT VOLTAGE (LSB)
+FS -
1
LSB
2
+FS =
VREF
+ COM
2
-FS =
-VREF
+ COM
2
COM =
VREF
2
1LSB =
VREF
256
Figure 12b. Bipolar Transfer Function
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1110CAP+ | IC ADC SRL 8CH8BIT 50KSPS 20SSOP |
| MS3102E22-6P | CONN RCPT 3POS BOX MNT W/PINS |
| VI-B5J-IV-F2 | CONVERTER MOD DC/DC 36V 150W |
| VE-BTK-MX-F2 | CONVERTER MOD DC/DC 40V 75W |
| A7FB | CONN PLUG CORD FMAL 7PIN BLK/SLV |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1108EUB+ | 功能描述:模數轉換器 - ADC 2Ch Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1108EUB+G07 | 功能描述:模數轉換器 - ADC 2Ch Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1108EUB+T | 功能描述:模數轉換器 - ADC 2Ch Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1108EUB+TG07 | 功能描述:模數轉換器 - ADC 2Ch Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1108EUB-G07 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。