- 您現在的位置：買賣IC網 > PDF目錄9873 > MAX11045ECB+ (Maxim Integrated Products)IC ADC 16BIT PAR 250KSPS 64TQFP PDF資料下載
參數資料
| 型號： | MAX11045ECB+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT PAR 250KSPS 64TQFP |
| 標準包裝： | 160 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 并聯 |
| 轉換器數目： | 6 |
| 功率耗散（最大）： | 3.48W |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
| 輸入數目和類型： | 6 個單端，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
4-/6-/8-Channel, 16-/14-Bit,
Simultaneous-Sampling ADCs
18
Maxim Integrated
MAX11044/MAX11044B/MAX11045/MAX11045B/
MAX11046/MAX11046B/MAX11054/MAX11055/MAX11056
Starting a Conversion
CONVST initiates conversions. The MAX11044/MAX11044B
MAX11045/MAX11045B/MAX11046/MAX11046B and
MAX11054/MAX11055/MAX11056 provide two acquisition
modes set through the configuration register. Allow a quiet
time (tQ) of 500ns prior to the start of conversion to avoid
any noise interference during readout or write operations
from corrupting a sample.
In default mode (CR0 = 0), drive CONVST low to place the
MAX11044/MAX11044B/MAX11045/MAX11045B/
MAX11046/MAX11046B and MAX11054/MAX11055/
MAX11056 into acquisition mode. All the input switches
are closed and the internal T/H circuits track the respective
input voltage. Keep the CONVST signal low for at least 1μs
(tACQ) to enable proper settling of the sampled voltages.
On the rising edge of CONVST, the switches are opened
and the MAX11044/MAX11044B/MAX11045/MAX11045B/
MAX11046/MAX11046B and MAX11054/MAX11055/
MAX11056 begin the conversion on all the samples in par-
allel. EOC remains high until the conversion is completed.
In the second mode (CR0 = 1), the MAX11044/
MAX11044B/MAX11045/MAX11045B/MAX11046/
MAX11046B and MAX11054/MAX11055/MAX11056
enter acquisition mode as soon as the previous conver-
sion is completed. CONVST rising edge initiates the
next sample and conversion sequence. CONVST needs
to be low for at least 20ns to be valid.
Provide adequate time for acquisition and the requisite
quiet time in both modes to achieve accurate sampling
and maximum performance of the MAX11044/
MAX11044B/MAX11045/MAX11045B/MAX11046/MAX1
1046B and MAX11054/MAX11055/MAX11056.
Reading Conversion Results
The CS and RD are active-low, digital inputs that con-
trol the readout through the 16-/14-bit, parallel, 20MHz
data bus (D0–D15/D13). After EOC transitions low, read
the conversion data by driving CS and RD low. Each
low period of RD presents the next channel’s result.
When CS or RD are high, the data bus is high imped-
ance. CS may be driven high between individual chan-
nel readouts or left low during the entire 8-channel
readout.
Reference
Internal Reference
The MAX11044/MAX11044B/MAX11045/MAX11045B/
MAX11046/MAX11046B and MAX11054/MAX11055/
MAX11056 feature a precision, low-drift, internal
bandgap reference. Bypass REFIO with a 0.1μF capaci-
tor to AGND to reduce noise. The REFIO output voltage
may be used as a reference for other circuits. The output
impedance of REFIO is 10k
Ω. Drive only high impedance
circuits or buffer externally when using REFIO to drive
external circuitry.
External Reference
Set the configuration register to disable the internal ref-
erence and drive REFIO with a high-quality external ref-
erence. To avoid signal degradation, ensure that the
integrated reference noise applied to REFIO is less
than 10μV in the bandwidth of up to 50kHz.
Sn
Sn + 1
t8
t12
t13
t9
t10
t11
RD
(USER SUPPLIED)
CS
(USER SUPPLIED)
DB0–DB15/DB13
Figure 5. Readout Timing Requirements
CONFIGURATION
REGISTER
t6
t3
t4
t5
t7
WR
(USER SUPPLIED)
CS
(USER SUPPLIED)
CR0–CR3
(USER SUPPLIED)
Figure 4. Programming Configuration-Register Timing
Requirements
相關PDF資料 |
PDF描述 |
|---|---|
| ISL3178AEMBZ-T | TXRX ESD 3.3V RS485/422 8-SOIC |
| ISL3158AEMBZ-T | TXRX ESD 5V RS485/422 8-SOIC |
| MAX1081AEUP+ | IC ADC 10BIT 300KSPS 20-TSSOP |
| MAX189BCPA+ | IC ADC 12BIT SERIAL LP 8-DIP |
| MAX189BCWE+ | IC ADC 12BIT SERIAL LP 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11045ECB+ | 功能描述:模數轉換器 - ADC 16Bit 6Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11045ECB+T | 功能描述:模數轉換器 - ADC 16Bit 6Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11045ETN+ | 功能描述:模數轉換器 - ADC 16Bit 6Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11045ETN+T | 功能描述:模數轉換器 - ADC 16Bit 6Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11046 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs |
發布緊急采購，3分鐘左右您將得到回復。