參數資料
型號: MAX11044ECB+
廠商: Maxim Integrated Products
文件頁數: 9/28頁
文件大?。?/td> 0K
描述: IC ADC 16BIT PAR 250KSPS 64TQFP
標準包裝: 160
位數: 16
采樣率(每秒): 250k
數據接口: 并聯
轉換器數目: 4
功率耗散(最大): 3.48W
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: *
封裝/外殼: *
供應商設備封裝: *
包裝: *
輸入數目和類型: 4 個單端,雙極
4-/6-/8-Channel, 16-/14-Bit,
Simultaneous-Sampling ADCs
17
Maxim Integrated
MAX11044/MAX11044B/MAX11045/MAX11045B/
MAX11046/MAX11046B/MAX11054/MAX11055/MAX11056
where VFAULT_MAX is the maximum voltage that the
source produces during a fault condition.
Figures 2 and 3 illustrate the clamp circuit voltage-cur-
rent characteristics for a source impedance RS =
1280
Ω. While the input voltage is within the ±(VAVDD +
300mV) range, no current flows in the input clamps.
Once the input voltage goes beyond this voltage range,
the clamps turn on and limit the voltage at the input pin.
Applications Information
Digital Interface
The bidirectional, parallel, digital interface, CR0–CR3,
sets the 4-bit configuration register. This interface con-
figures the following control signals: chip select (CS),
read (RD), write (WR), end of conversion (EOC), and
convert start (CONVST). Figures 6 and 7 and the
Timing Characteristics in the
Electrical Characteristics
table show the operation of the interface.
DB0–DB15/DB13 output the 16-/14-bit conversion result.
All bits are high impedance when RD = 1 or CS = 1.
CR3 (Int/Ext Reference)
CR3 selects the internal or external reference. The POR
default = 0.
0 = internal reference, REFIO internally driven through a
10k
Ω resistor, bypass with 0.1μF capacitor to AGND.
1 = external reference, drive REFIO with a high-quality
reference.
CR2 (Output Data Format)
CR2 selects the output data format. The POR default = 0.
0 = offset binary.
1 = two’s complement.
CR1 (Reserved)
CR1 must be set to 0.
CR0 (CONVST Mode)
CR0 selects the acquisition mode. The POR default = 0.
0 = CONVST controls the acquisition and conversion.
Drive CONVST low to start acquisition. The rising edge
of CONVST begins the conversion.
1 = acquisition mode starts as soon as the previous
conversion is complete. The rising edge of CONVST
begins the conversion.
Programming the Configuration Register
To program the configuration register, bring the CS and
WR low and apply the required configuration data on
CR3–CR0 of the bus and then raise WR once to save
changes.
CAUTION: When the configuration register is not
being programmed, the host driving CR3–CR0 must
relinquish the bus when the conversion results of
the ADC are being read!
R
VV
mA
S
FAULT MAX
_
=
-7
20
CR3
CR2
CR1
CR0
Int/Ext
Reference
Output
Data Format
Must be set
to 0
CONVST
Mode
Table 1. Configuration Register
MAX11044
fig02
SIGNAL VOLTAGE AT SOURCE AND PIN (V)
I CLAMP
(mA)
-10
-30
30
10
30
-30
10
-10
-20
20
0
-50
50
RS = 1280
Ω
VAVDD = 5V
AT CH_ INPUT
AT SOURCE
Figure 2. Input Clamp Characteristics
MAX11044
fig03
SIGNAL VOLTAGE AT SOURCE AND PIN (V)
I CLAMP
(mA)
-4
-6
246
0
-2
30
-30
10
-10
-20
20
0
-8
8
RS = 1280
Ω
VAVDD = 5V
AT CH_ INPUT
AT SOURCE
Figure 3. Input Clamp Characteristics (Zoom In)
相關PDF資料
PDF描述
MS27472E18F35S CONN RCPT 66POS WALL MNT W/SCKT
MAX1065ACUI+T IC ADC 14BIT 165KSPS 28TSSOP
MAX1066ACUP+T IC ADC 14BIT 165KSPS 20TSSOP
MAX187CEWE+T IC ADC 12BIT SERIAL LP 16SOIC
MAX1275AETC+ IC ADC 12BIT 1.8MSPS 12-TQFN
相關代理商/技術參數
參數描述
MAX11044ECB+ 功能描述:模數轉換器 - ADC 16Bit 4Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11044ECB+T 功能描述:模數轉換器 - ADC 16Bit 4Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11044ETN+ 功能描述:模數轉換器 - ADC 16Bit 4Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11044ETN+ 制造商:Maxim Integrated Products 功能描述:IC ADC 16BIT 250KSPS TQFN-56
MAX11044ETN+T 功能描述:模數轉換器 - ADC 16Bit 4Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32