- 您現在的位置：買賣IC網 > PDF目錄383309 > MAX1099BEAE (MAXIM INTEGRATED PRODUCTS INC) 10-Bit Serial-Output Temperature Sensors with 5-Channel ADC PDF資料下載
參數資料
| 型號： | MAX1099BEAE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 10-Bit Serial-Output Temperature Sensors with 5-Channel ADC |
| 中文描述： | 5-CH 10-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | 5.30 MM, 0.65 MM PITCH, SSOP-16 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 240K |
| 代理商： | MAX1099BEAE |
M
10-Bit Serial-Output Temperature Sensors
with 5-Channel ADC
16
______________________________________________________________________________________
ence reflects the power requirement of an internal refer-
ence buffer amplifier that can accommodate external
loads. Temperature conversions at 100% duty cycle
increase supply currents to 440μA (400μA) through
additional amplification, buffer, and bias circuitry that is
otherwise inactive.
Place the MAX1098/MAX1099 in a low-current power-
down state between conversions to conserve power.
Select standby, standby plus, or shutdown through bits
PM1 and PM0 of the initialization byte (Table 3).
The MAX1098/MAX1099 assume the shutdown power
mode when V
DD
is first applied.
Standby Mode
Standby mode turns off the MAX1098/MAX1099 ADC,
internal clock, and reference buffer amplifier. Special
circuitry for temperature conversions is also deactivat-
ed. Wake-up time is limited by the reference buffer
amplifier and the associated bypass capacitor (see
Internal Reference
). When an external reference is
used, wake-up time is 0.1ms.
Standby-Plus Mode
Standby-plus mode is similar to the standby mode, but
the internal reference output buffer remains active to
shorten the wake-up time to 0.1ms for internal refer-
ence mode. When using an external reference, stand-
by-plus mode is equivalent to standby mode.
Shutdown Mode
Shutdown mode turns off all functions other than start-
up circuitry, thereby reducing typical supply current to
2μA. Data registers are cleared. Use this power mode
when interconversion times are no less than 5ms.
Monitoring V
DD
This mode of operation samples and converts the sup-
ply voltage, V
DD
/4, which is internally generated. The
reference voltage must be larger than V
DD
/8 for the
operation to work properly. From the result of a conver-
sion (CODE), CODE = 64 V
DD
/ V
REF
.
Temperature Measurements
The MAX1098/MAX1099 perform temperature measure-
ments with internal or external diode-connected transis-
tors through a three-step process. First, the diode bias
current changes from 31.6μA to 10μA to produce a
temperature-dependent bias voltage difference, which
is amplified by a factor of 20 and converted to digital
format. Second, the bias current changes from 31.6μA
to 100μA, and the bias voltage difference is similarly
amplified by a factor of 20 and converted to digital for-
mat. Third, the intermediate results are subtracted to
achieve a digital output that is proportional to absolute
temperature in degrees Kelvin.
The reference voltage used in conjunction with tempera-
ture measurements is derived from the internal reference
source to ensure that 1LSB corresponds to 1/8 of a
degree. To convert to degrees Celsius, subtract 273.15
from the temperature inferred from the ADC output.
Temperature measurements require a conversion time
of 2.2ms.
Shield Output Buffer
The MAX1098/MAX1099 provide a shield output buffer
voltage at SHO that is approximately 0.6V (one diode
drop) above V
DD
/2. When performing temperature
measurements with an external diode, use this voltage
to suppress error-producing leakage currents (see
Remote Diode Shielding
). Figure 7 shows the SHO out-
put circuit.
Applications Information
Remote Diode Selection
Temperature accuracy depends on having a good-
quality, diode-connected, small-signal transistor.
Accuracy has been experimentally verified for 2N3904
devices. CPUs and other ICs having on-board temper-
ature-sensing diodes can also be monitored if the
diode connections are floating.
Table 3. Power-Mode Selection
See Power Requirements in
Electrical Characteristics.
PM1
0
0
1
PM0
0
1
0
MODE
Shutdown
Standby plus
Standby
1
1
Normal operation
5
μ
A
SHO
V
DD
2
Figure 7. SHO Output Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1099CEAE | 10-Bit Serial-Output Temperature Sensors with 5-Channel ADC |
| MAX1108-MAX1109 | Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs |
| MAX1108CUB | Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs |
| MAX1108 | Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs |
| MAX1108EUB | Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1099BEAE+ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1099BEAE+T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1099BEAE-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1099CEAE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1099CEAE+ | 功能描述:板上安裝溫度傳感器 10Bit SerialOut Temp Sensor w/5Ch ADC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。