- 您現在的位置：買賣IC網 > PDF目錄9907 > MAX1093BCEG+ (Maxim Integrated Products)IC ADC 10BIT 250KSPS 24-QSOP PDF資料下載
參數資料
| 型號： | MAX1093BCEG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 250KSPS 24-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 10 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 762mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
MAX1091/MAX1093
250ksps, +3V, 8-/4-Channel, 10-Bit ADCs
with +2.5V Reference and Parallel Interface
______________________________________________________________________________________
17
Table 6. Full-Scale and Zero-Scale for Unipolar and Bipolar Operation
UNIPOLAR MODE
BIPOLAR MODE
COM
Zero Scale
—
-VREF/2 + COM
Negative Full Scale
—
VREF + COM
VREF/2 + COM
Positive Full Scale
Full Scale
sion cycles, and 2 read cycles. This assumes that the
results of the last conversion are read before the next
control byte is written. Throughputs up to 300ksps can
be achieved by first writing a control word to begin the
acquisition cycle of the next conversion, and then read-
ing the results of the previous conversion from the bus
(Figure 10). This technique allows a conversion to be
completed every 16 clock cycles. Note that the switch-
ing of the data bus during acquisition or conversion can
cause additional supply noise, which can make it diffi-
cult to achieve true 10-bit performance.
Layout, Grounding, and Bypassing
For best performance, use printed circuit (PC) boards.
Wire-wrap configurations are not recommended since
the layout should ensure proper separation of analog
and digital traces. Do not run analog and digital lines
parallel to each other, and don’t lay out digital signal
paths underneath the ADC package. Use separate
analog and digital PC board ground sections with only
one star point (Figure 11) connecting the two ground
systems (analog and digital). For lowest-noise opera-
tion, ensure the ground return to the star ground’s
power supply is low impedance and as short as possi-
ble. Route digital signals far away from sensitive analog
and reference inputs.
High-frequency noise in the power supply (VDD) could
influence the proper operation of the ADC’s fast com-
parator. Bypass VDD to the star ground with a network
of two parallel capacitors, 0.1F and 4.7F, located as
close as possible to the MAX1091/MAX1093s’ power-
supply pin. Minimize capacitor lead length for best sup-
ply-noise rejection; add an attenuation resistor (5
) if
the power supply is extremely noisy.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. The sta-
tic linearity parameters for the MAX1091/MAX1093 are
measured using the end-point method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1 LSB. A
DNL error specification of less than 1 LSB guarantees
no missing codes and a monotonic transfer function.
Aperture Definitions
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between the samples. Aperture delay (tAD) is
the time between the rising edge of the sampling clock
and the instant when an actual sample is taken.
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital
samples, signal-to-noise ratio (SNR) is the ratio of the
full-scale analog input (RMS value) to the RMS quanti-
zation error (residual error). The ideal, theoretical mini-
mum analog-to-digital noise is caused by quantization
error only and results directly from the ADC’s resolution
(N bits):
SNR = (6.02 x N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. Therefore, SNR is computed by taking the ratio of
the RMS signal to the RMS noise which includes all
spectral components minus the fundamental, the first
five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion
Signal-to-noise plus distortion (SINAD) is the ratio of the
fundamental input frequency’s RMS amplitude to the
RMS equivalent of all other ADC output signals:
SINAD (dB) = 20 x log (SignalRMS / NoiseRMS)
Effective Number of Bits
Effective number of bits (ENOB) indicates the global
accuracy of an ADC at a specific input frequency and
sampling rate. An ideal ADC’s error consists of quanti-
zation noise only. With an input range equal to the full-
scale range of the ADC, calculate the effective number
of bits as follows:
ENOB = (SINAD - 1.76) / 6.02
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72T3685L5BB | IC FIFO 16384X36 5NS 208-BGA |
| V48A12T500BL | CONVERTER MOD DC/DC 12V 500W |
| IDT72T1885L5BB | IC FIFO 32768X18 2.5V 5NS 144BGA |
| MAX189BCWE+T | IC ADC 12BIT SERIAL LP 16SOIC |
| MAX1240AESA/V+T | IC ADC 12BIT SRL 73KSPS 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1093BCEG+ | 功能描述:模數轉換器 - ADC 250ksps 4Ch 10-Bit w/Internal 2.5V ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1093BCEG+T | 功能描述:模數轉換器 - ADC 250ksps 4Ch 10-Bit w/Internal 2.5V ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1093BCEG-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1093BEEG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1093BEEG+ | 功能描述:模數轉換器 - ADC 250ksps 4Ch 10-Bit w/Internal 2.5V ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。