參數資料
型號： MAX1078CTC+
廠商： Maxim Integrated Products
文件頁數： 6/18頁
文件大?。?/td> 0K
描述： IC ADC 10BIT 1.8MSPS 12-TQFN
標準包裝： 75
位數： 10
采樣率（每秒）： 1.8M
數據接口： MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 50mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 12-WQFN 裸露焊盤
供應商設備封裝： 12-TQFN-EP（4x4）
包裝： 管件
輸入數目和類型： 1 個差分，雙極
SCLK, and the transmit frame sync (FSX) drives the
receive frame sync (FSR) and CNVST.
For continuous conversion, set the serial port to trans-
mit a clock, and pulse the frame sync signal for a clock
period before data transmission. The serial-port config-
uration (SPC) register should be set up with internal
frame sync (TXM = 1), CLKX driven by an on-chip clock
source (MCM = 1), burst mode (FSM = 1), and 16-bit
word length (FO = 0).
This setup allows continuous conversions provided that
the data-transmit register (DXR) and the data-receive
register (DRR) are serviced before the next conversion.
Alternatively, autobuffering can be enabled when using
the buffered serial port to execute conversions and
read the data without CPU intervention. Connect the VL
pin to the TMS320C54_ supply voltage when the
MAX1076/MAX1078 are operating with an analog sup-
ply voltage higher than the DSP supply voltage. The
word length can be set to 8 bits with FO = 1 to imple-
ment the power-down modes. The CNVST pin must idle
high to remain in either power-down state.
Another method of connecting the MAX1076/MAX1078
to the TMS320C54_ is to generate the clock signals
external to either device. This connection is shown in
Figure 16 where serial clock (CLOCK) drives the CLKR
and SCLK and the convert signal (CONVERT) drives
the FSR and CNVST.
The serial port must be set up to accept an external
receive-clock and external receive-frame sync.
The SPC register should be written as follows:
TXM = 0, external frame sync
MCM = 0, CLKX is taken from the CLKX pin
FSM = 1, burst mode
FO = 0, data transmitted/received as 16-bit words
This setup allows continuous conversion, provided that
the DRR is serviced before the next conversion.
Alternatively, autobuffering can be enabled when using
the buffered serial port to read the data without CPU
intervention. Connect the VL pin to the TMS320C54_
supply voltage when the MAX1076/MAX1078 are oper-
ating with an analog supply voltage higher than the
DSP supply voltage.
The MAX1076/MAX1078 can also be connected to the
TMS320C54_ by using the data transmit (DX) pin to
drive CNVST and the CLKX generated internally to
drive SCLK. A pullup resistor is required on the CNVST
signal to keep it high when DX goes high impedance
and 0001hex should be written to the DXR continuously
for continuous conversions. The power-down modes
may be entered by writing 00FFhex to the DXR (see
Figures 17 and 18).
DSP Interface to the ADSP21_ _ _
The MAX1076/MAX1078 can be directly connected to
the ADSP21_ _ _ family of DSPs from Analog Devices,
Inc. Figure 19 shows the direct connection of the
MAX1076/MAX1078 to the ADSP21_ _ _. There are two
modes of operation that can be programmed to interface
with the MAX1076/MAX1078. For continuous conver-
sions, idle CNVST low and pulse it high for one clock
cycle during the LSB of the previous transmitted word.
The ADSP21_ _ _ STCTL and SRCTL registers should be
configured for early framing (LAFR = 0) and for an
active-high frame (LTFS = 0, LRFS = 0) signal. In this
mode, the data-independent frame-sync bit (DITFS = 1)
can be selected to eliminate the need for writing to the
transmit-data register more than once. For single conver-
MAX1076/MAX1078
1.8Msps, Single-Supply, Low-Power, True-
Differential, 10-Bit ADCs with Internal Reference
14
______________________________________________________________________________________
Figure 15. Interfacing to the TMS320C54_ Internal Clocks
Figure 16. Interfacing to the TMS320C54_ External Clocks
MAX1076
MAX1078
TMS320C54_
VL
SCLK
CNVST
DOUT
DVDD
CLKR
FSR
CLKX
FSX
DR
MAX1076
MAX1078
TMS320C54_
VL
DVDD
SCLK
CLKR
CNVST
FSR
DOUT
DR
CLOCK
CONVERT
相關PDF資料
PDF描述
MAX3941ETG+ IC EAM DRIVER 10GBPS 24-TQFN
NB7L216MNR2G IC RECEIVER/DRIVER DIFF 16-QFN
VI-260-IU-F4 CONVERTER MOD DC/DC 5V 200W
DS3154N# IC LIU DS3/E3/STS-1 144-CSBGA
MAX1075CTC+ IC ADC 10BIT 1.8MSPS 12-TQFN
相關代理商/技術參數
參數描述
MAX1078CTC+ 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1078CTC+T 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1078CTC-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1078ETC 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1078ETC+ 功能描述:模數轉換器 - ADC 10Bit 1.8Msps Single Sply True Diff RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*