- 您現在的位置：買賣IC網 > PDF目錄9889 > MAX1068CEEG+T (Maxim Integrated Products)IC ADC 14BIT 200KSPS 24-QSOP PDF資料下載
參數資料
| 型號： | MAX1068CEEG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/30頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 200KSPS 24-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 14 |
| 采樣率（每秒）： | 200k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 762mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
DSP 8-Bit-Wide Data-Transfer Mode (External Clock
Mode, MAX1068 Only)
Figure 16 shows the DSP-interface timing diagram.
Logic low at DSPR on the falling edge of CS enables
DSP interface mode. After the MAX1068 enters DSP
mode, CS can remain low for the duration of the con-
version process and each subsequent conversion.
Drive DSEL low to select the 8-bit data-transfer mode.
A sync pulse from the DSP at DSPR wakes the analog
circuitry and allows SCLK to clock in data (Figure 17).
The frame sync pulse alerts the MAX1068 that incom-
ing data is about to be sent to DIN. Ensure the duty
cycle on SCLK is between 45% and 55% when operat-
ing at 4.8MHz (the maximum clock frequency). For
lower clock frequencies, ensure the minimum high and
low times are at least 93ns. External clock mode con-
versions with SCLK rates less than 125kHz can reduce
accuracy due to leakage of the sampling capacitor.
The input data latches on the falling edge of SCLK. The
command/configuration/control register starts reading
data in on the falling edge of the first SCLK cycle imme-
diately following the falling edge of the frame sync
pulse and ends on the falling edge of the 8th SCLK
cycle. The MAX1068 selects the proper channel for
conversion on the falling edge of the 3rd clock cycle
and begins acquisition. Acquisition continues until the
rising edge of the 7th clock cycle. The MAX1068 sam-
ples the input on the rising edge of the 7th clock cycle.
On the rising edge of the 8th clock cycle, the MAX1068
outputs a frame sync pulse at DSPX. The frame sync
pulse alerts the DSP that the conversion results are
about to be output at DOUT (MSB first) starting on the
rising edge of the 9th clock pulse. To read the entire
conversion results, 16 SCLK cycles are needed. Extra
clock pulses, occuring after the conversion result has
been clocked out, and prior to the next rising edge of
DSPR, cause zeros to be clocked out of DOUT. The
MAX1068 external-clock, DSP 8-bit-wide data-transfer
mode requires 24 clock cycles to complete.
Begin a new conversion by sending a new frame sync
pulse to DSPR followed by new configuration data.
Send the new DSPR pulse immediately after reading
the conversion result to realize maximum throughput.
Sending a new frame sync pulse in the middle of a con-
version immediately aborts the current conversion and
begins a new one. A rising edge on CS in the middle of
a conversion aborts the current conversion and places
the MAX1068 in shutdown.
DSP 16-Bit-Wide Data-Transfer Mode (External
Clock Mode, MAX1068 Only)
Figure 16 shows the DSP-interface timing diagram. Logic
low at DSPR on the falling edge of CS enables DSP inter-
face mode. After the MAX1068 enters DSP mode, CS
can remain low for the duration of the conversion
process and each subsequent conversion. The acquisi-
tion time is extended an extra eight SCLK cycles in the
16-bit-wide data-transfer mode. Drive DSEL high to
select the 16-bit-wide data-transfer mode. A sync pulse
from the DSP at DSPR wakes the analog circuitry and
allows SCLK to clock in data (Figure 18). The frame
sync pulse also alerts the MAX1068 that incoming data
is about to be sent to DIN. Ensure the duty cycle on
SCLK is between 45% and 55% when operating at
MAX1067/MAX1068
Multichannel, 14-Bit, 200ksps Analog-to-Digital
Converters
______________________________________________________________________________________
21
CS
SCLK
DSPR
DIN
DOUT
tCSS
tCL
tDS
tDH
tDV
tCH
tDO
tTR
tFSH
tCSH
tDF
tCP
tCSW
tFSS
...
Figure 16. Detailed DSP-Interface Timing (MAX1068 Only)
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72T18125L5BB | IC FIFO 524X18 2.5V 5NS 240BGA |
| VI-J3T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| ICL3232ECV-20ZT | IC 2DRVR/2RCVR RS232 3V 20-TSSOP |
| MAX166ACWP+ | IC ADC 8BIT MPU COMP 20-SOIC |
| ICL3232ECV-20Z | IC 2DRVR/2RCVR RS232 3V 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1069 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:58.6ksps, 14-Bit, 2-Wire Serial ADC in a 14-Pin TSSOP |
| MAX1069_10 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:58.6ksps, 14-Bit, 2-Wire Serial ADC in a 14-Pin TSSOP |
| MAX1069ACUD | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1069ACUD+ | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1069ACUD+T | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。