- 您現在的位置：買賣IC網 > PDF目錄2085 > MAX1067BCEE+ (Maxim Integrated Products)IC ADC 14-BIT 200KSPS 16-QSOP PDF資料下載
參數資料
| 型號： | MAX1067BCEE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14-BIT 200KSPS 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 位數： | 14 |
| 采樣率（每秒）： | 200k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 667mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX1067/MAX1068
Internal Clock 16-Bit-Wide Data-Transfer and
Scan Mode (MAX1068 Only)
Force DSPR high and DSEL low for the SPI/QSPI/
MICROWIRE-interface mode. The falling edge of CS
wakes the analog circuitry and allows SCLK to clock in
data (see Figure 13). DOUT changes from high-Z to logic
low after CS is brought low. Input data latches on the ris-
ing edge of SCLK. The command/configuration/control
register begins reading DIN on the first SCLK rising
edge and ends on the rising edge of the 8th SCLK
cycle. The MAX1068 selects the proper channel for
conversion on the rising edge of the 3rd SCLK cycle.
The internal oscillator activates 125ns after the rising
edge of the 16th SCLK cycle. Turn off the external
clock while the internal clock is on. Turning off SCLK
ensures lowest noise performance during acquisition.
Acquisition begins on the 2nd rising edge of the inter-
nal clock and ends on the falling edge of the 18th inter-
nal clock cycle. Each bit of the conversion result shifts
into memory as it becomes available. The conversion
result is available (MSB first) at DOUT on the falling
edge of EOC. The internal oscillator and analog circuit-
ry are shut down on the EOC high-to-low transition. Use
the EOC high-to-low transition as the signal to restart
the external clock (SCLK). To read the entire conver-
sion result, 16 SCLK cycles are needed. Extra clock
pulses, occurring after the conversion result has been
clocked out and prior to the rising edge of CS, cause
the conversion result to be shifted out again. The
MAX1068 internal-clock 16-bit-wide data-transfer mode
requires 32 external clock cycles and 32 internal clock
cycles for completion.
Force CS high after the conversion result is read. For
maximum throughput, force CS low again to initiate the
next conversion immediately after the specified mini-
mum time (tCSW). Forcing CS high in the middle of a
conversion immediately aborts the conversion and
places the MAX1068 in shutdown.
Scan mode allows multiple channels to be scanned
consecutively or one channel to be scanned eight
times. Scan mode can only be enabled when using the
MAX1068 in internal clock mode. Enable scanning by
setting bits 4 and 3 in the command/configuration/con-
trol register (see Tables 3 and 4). In scan mode, conver-
sion results are stored in memory until the completion of
the last conversion in the sequence. Upon completion of
the last conversion in the sequence, EOC transitions
from high to low to indicate the end of the conversion
and shuts down the internal oscillator. Use the EOC
high-to-low transition as the signal to restart the external
clock (SCLK). DOUT provides the conversion results in
the same order as the channel conversion process. The
MSB of the first conversion is available at DOUT on the
falling edge of EOC. Figure 15 shows the timing dia-
gram for 16-bit-wide data transfer in scan mode.
Multichannel, 14-Bit, 200ksps Analog-to-Digital
Converters
20
______________________________________________________________________________________
DOUT
CS
SCLK
DIN
EOC
ADC
STATE
INTERNAL
CLK
1
89
16
X = DON
,
T CARE
2
13
17
45
48
64
32
34
X X X X X X X X
DATA
LSB
S1
S0
X
tACQ
POWER-DOWN
tCONV
tACQ
tCONV
MSB
Figure 15. SPI Internal Clock Mode, 16-Bit Data-Transfer Mode, Scan Mode for Two Conversions, Conversion Timing (MAX1068 Only)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1069BEUD+ | IC ADC 14BIT I2C 58KSPS 14-TSSOP |
| MAX1070CTC+T | IC ADC 10BIT 1.5MSPS 12-TQFN |
| MAX1075CTC+T | IC ADC 10BIT 1.8MSPS 12-TQFN |
| MAX1078CTC+T | IC ADC 10BIT 1.8MSPS 12-TQFN |
| MAX1079CTC+T | IC ADC 10BIT 1.5MSPS 12-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1067BCEE+ | 功能描述:模數轉換器 - ADC MultiCh 14-Bit 200ksps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1067BCEE+T | 功能描述:模數轉換器 - ADC MultiCh 14-Bit 200ksps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1067BCEE-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1067BEEE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1067BEEE+ | 功能描述:模數轉換器 - ADC MULTICH 200KSPS ANLG-DGTL CNVTRS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。