參數資料
型號: MAX1066CEUP
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface
中文描述: 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO20
封裝: 4.40 MM, TSSOP-28
文件頁數: 8/14頁
文件大?。?/td> 335K
代理商: MAX1066CEUP
M
Detailed Description
Converter Operation
The MAX1065/MAX1066 use a successive-approximation
(SAR) conversion technique with an inherent track-and-
hold (T/H) stage to convert an analog input into a 14-bit
digital output. Parallel outputs provide a high-speed inter-
face to most microprocessors (μPs). The
Functional
Diagram
shows a simplified internal architecture of the
MAX1065/MAX1066. Figure 3 shows a typical application
circuit for the MAX1066.
Analog Input
The equivalent input circuit is shown in Figure 4. A
switched capacitor digital-to-analog converter (DAC)
provides an inherent track-and-hold function. The sin-
gle-ended input is connected between AIN and AGND.
Input Bandwidth
The ADC
s input-tracking circuitry has a 4MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC
s sampling rate by
using undersampling techniques. To avoid aliasing of
unwanted high-frequency signals into the frequency
band of interest, use antialias filtering.
Internal protection diodes, which clamp the analog
input to AV
DD
and/or AGND, allow the input to swing
from AGND - 0.3V to AV
DD
+ 0.3V, without damaging
the device.
If the analog input exceeds 300mV beyond the sup-
plies, limit the input current to 10mA.
Track and Hold (T/H)
In track mode, the analog signal is acquired on the
internal hold capacitor. In hold mode, the T/H switches
open and the capacitive DAC samples the analog input.
Low-Power, 14-Bit Analog-to-Digital Converters
with Parallel Interface
8
_______________________________________________________________________________________
CS
R/C
REF POWER-
DOWN BIT
EOC
D0
D13
HBEN*
DATA VALID
D7/D13
D0/D8*
HIGH/LOW
BYTE VALID
t
ACQ
t
CONV
t
CSH
t
CSL
t
DH
t
DO
t
DO1
t
EOC
*HBEN AND BYTE-WIDE DATA BUS AVAILABLE ON MAX1066 ONLY.
t
DS
t
DV
HI
Z
HI-Z
HIGH/LOW
BYTE VALID
t
BR
t
BR
Figure 2. MAX1065/MAX1066 Timing Diagram
DGND
1mA
C
LOAD
= 20pF
D0
D13
D0
D13
C
LOAD
= 20pF
1mA
DGND
DV
DD
a) HIGH-Z TO V
OH,
V
OL
TO V
AND
V
OH
TO HIGH-Z
b) HIGH-Z TO V
OL,
V
OH
TO V
OL,
AND
V
OL
TO HIGH-Z
Figure 1. Load Circuits for D0–D13 Enable Time,
CS
to D0–D13
Delay Time and Bus Relinquish Time
相關PDF資料
PDF描述
MAX107 Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier
MAX107ECS Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier
MAX1091BEEI 250ksps, +3V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface
MAX1091ACEI 250ksps, +3V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface
MAX1093ACEG IGBT Module; Continuous Collector Current, Ic:400A; Collector Emitter Saturation Voltage, Vce(sat):2.4V; Power Dissipation, Pd:2800W; C-E Breakdown Voltage:1200V; Collector Current:400A; Collector Emitter Voltage, Vceo:3.4V RoHS Compliant: No
相關代理商/技術參數
參數描述
MAX1067 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Multichannel, 14-Bit, 200ksps Analog-to-Digital Converters
MAX1067ACEE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1067ACEE-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1067AEEE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32