- 您現在的位置：買賣IC網 > PDF目錄9888 > MAX1064BEEG+ (Maxim Integrated Products)IC ADC 10BIT 400KSPS 24-QSOP PDF資料下載
參數資料
| 型號： | MAX1064BEEG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 400KSPS 24-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 10 |
| 采樣率（每秒）： | 400k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 762mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
MAX1060/MAX1064
400ksps, +5V, 8-/4-Channel, 10-Bit ADCs
with +2.5V Reference and Parallel Interface
______________________________________________________________________________________
11
Table 1. Control Byte Functional Description
NAME
FUNCTION
D4
0
SGL/DIF
SGL/DIF = 0: Pseudo-differential analog input mode
SGL/DIF = 1: Single-ended analog input mode
In single-ended mode, input signals are referred to COM. In pseudo-differential mode, the voltage
difference between two channels is measured (Tables 2 and 3).
1
0
D3
UNI/BIP
Standby power-down mode. Clock mode is unaffected.
0
1
UNI/BIP = 0: Bipolar mode
UNI/BIP = 1: Unipolar mode
In unipolar mode, an analog input signal from 0 to VREF can be converted; in bipolar mode, the
signal can range from -VREF/2 to +VREF/2.
D2, D1, D0
Normal operation mode. External clock mode is selected.
1
A2, A1, A0
Address bits A2, A1, A0 select which of the 8/4 (MAX1060/MAX1064) channels are to be converted
(Tables 3 and 4).
Normal operation mode. Internal clock mode is selected.
BIT
PD1, PD0
0
D7, D6
PD1 and PD0 select the various clock and power-down modes.
Full power-down mode. Clock mode is unaffected.
D5
ACQMOD
ACQMOD = 0: Internal acquisition mode
ACQMOD = 1: External acquisition mode
the acquisition interval. The ACQMOD (acquisition
mode) bit in the input control byte (Table 1) offers two
options for acquiring the signal: an internal and an
external acquisition. The conversion period lasts for 13
clock cycles in either the internal or external clock or
acquisition mode. Writing a new control byte during a
conversion cycle aborts the conversion and starts a
new acquisition interval.
Internal Acquisition
Select internal acquisition by writing the control byte
with the ACQMOD bit cleared (ACQMOD = 0). This
causes the write pulse to initiate an acquisition interval
whose duration is internally timed. Conversion starts
when this acquisition interval (three external clock
cycles or approximately 1s in internal clock mode)
ends (Figure 4). When the internal acquisition is com-
bined with the internal clock, the aperture jitter can be
as high as 200ps. Internal clock users wishing to
achieve the 50ps jitter specification should always use
external acquisition mode.
External Acquisition
Use external acquisition mode for precise control of the
sampling aperture and/or dependent control of acquisi-
tion and conversion times. The user controls acquisition
and start-of-conversion with two separate write pulses.
The first pulse, written with ACQMOD = 1, starts an
acquisition interval of indeterminate length. The second
write pulse, written with ACQMOD = 0 (all other bits in
the control byte are unchanged), terminates acquisition
and starts conversion on WR rising edge (Figure 5).
The address bits for the input multiplexer must have the
same values on the first and second write pulses.
Power-down mode bits (PD0, PD1) can assume new
values on the second write pulse (see the Power-Down
Modes section). Changing other bits in the control byte
corrupts the conversion.
Reading a Conversion
A standard interrupt signal, INT, is provided to allow the
MAX1060/MAX1064 to flag the P when the conversion
has ended and a valid result is available. INT goes low
when the conversion is complete and the output data is
ready (Figures 4 and 5). INT returns high on the first
read cycle or if a new control byte is written.
Selecting Clock Mode
The MAX1060/MAX1064 operate with an internal or
external clock. Control bits D6 and D7 select either
internal or external clock mode. The part retains the
last-requested clock mode if a power-down mode is
selected in the current input word. For both internal and
external clock modes, internal or external acquisition
can be used. At power-up, the MAX1060/MAX1064
enter the default external clock mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1063BEEG+ | IC ADC 10BIT 250KSPS +3V 24-QSOP |
| MS27656T17B99SA | CONN RCPT 23POS WALL MNT W/SCKT |
| MAX150BCWP+T | IC ADC 8BIT W/REF T/H 20-SOIC |
| MAX156BCWI+ | IC ADC 8BIT 4CH T/H&REF 28-SOIC |
| D38999/26WF32SC | CONN PLUG 32POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1064BEEG+ | 功能描述:模數轉換器 - ADC 5V 10Bit 4Ch 400ksps w/2.5V Ref & Prl Int RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1064BEEG+T | 功能描述:模數轉換器 - ADC 5V 10Bit 4Ch 400ksps w/2.5V Ref & Prl Int RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1064BEEG-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1065 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power.14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1065_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
發布緊急采購，3分鐘左右您將得到回復。