參數資料
型號： MAX1030BCEG+T
廠商： Maxim Integrated Products
文件頁數： 9/22頁
文件大小： 0K
描述： IC ADC 10BIT 300KSPS 24-QSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
位數： 10
采樣率（每秒）： 300k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 9.5mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 帶卷 (TR)
輸入數目和類型： 16 個單端，單極；16 個單端，雙極；8 個差分，單極；8 個差分，雙極
MAX1026/MAX1028/MAX1030
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
17
Internally Timed Acquisitions and
Conversions Using
CNVST
Performing Conversions in Clock Mode 00
In clock mode 00, the wake up, acquisition, conversion,
and shutdown sequences are initiated through
CNVST
and performed automatically using the internal oscilla-
tor. Results are added to the internal FIFO to be read
out later. See Figure 4 for clock mode 00 timing.
Initiate a scan by setting
CNVST low for at least 40ns
before pulling it high again. The MAX1026/MAX1028/
MAX1030 then wake up, scan all requested channels,
store the results in the FIFO, and shut down. After the
scan is complete,
EOC is pulled low and the results are
available in the FIFO. Wait until
EOC goes low before
pulling
CS low to communicate with the serial interface.
EOC stays low until CS or CNVST is pulled low again. A
temperature measurement result, if requested, pre-
cedes all other FIFO results.
Do not initiate a second
CNVST before EOC goes low;
otherwise, the FIFO can become corrupted.
Externally Timed Acquisitions and
Internally Timed Conversions with
CNVST
Performing Conversions in Clock Mode 01
In clock mode 01, conversions are requested one at a
time using
CNVST and performed automatically using
the internal oscillator. See Figure 5 for clock mode 01
timing.
Setting
CNVST low begins an acquisition, wakes up the
ADC, and places it in track mode. Hold
CNVST low for
at least 1.4μs to complete the acquisition. If the internal
reference needs to wake up, an additional 65μs is
required for the internal reference to power up. If a tem-
perature measurement is being requested, reference
power-up and temperature measurement are internally
timed. In this case, hold
CNVST low for at least 40ns.
Set
CNVST high to begin a conversion. After the con-
version is complete, the ADC shuts down and pulls
EOC low. EOC stays low until CS or CNVST is pulled
low again. Wait until
EOC goes low before pulling CS or
CNVST low.
If averaging is turned on, multiple
CNVST pulses need
to be performed before a result is written to the FIFO.
Once the proper number of conversions has been per-
formed to generate an averaged FIFO result, as speci-
fied by the averaging register, the scan logic
automatically switches the analog input multiplexer to
the next-requested channel. If a temperature measure-
ment is programmed, it is performed after the first rising
edge of
CNVST following the input data byte written to
the conversion register. The result is available on DOUT
once
EOC has been pulled low.
(UP TO 514 INTERNALLY CLOCKED ACQUISITIONS AND CONVERSIONS)
CS
DOUT
MSB1
LSB1
MSB2
SCLK
CNVST
EOC
SET CNVST LOW FOR AT LEAST 40ns TO BEGIN A CONVERSION. X = DON'T CARE.
Figure 4. Clock Mode 00
相關PDF資料
PDF描述
V72B28M250BF CONVERTER MOD DC/DC 28V 250W
VE-B6X-IV-F1 CONVERTER MOD DC/DC 5.2V 150W
VI-B1J-MW-F2 CONVERTER MOD DC/DC 36V 100W
VE-B6W-IV-F4 CONVERTER MOD DC/DC 5.5V 150W
VI-B1L-MW-F2 CONVERTER MOD DC/DC 28V 100W
相關代理商/技術參數
參數描述
MAX1030BCGI-T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference
MAX1030BCTI 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1030BCTI+ 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1030BCTI+T 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1030BCTI-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*