- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX038EWP (MAXIM INTEGRATED PRODUCTS INC) Circular Connector; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:18; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:18-18; MIL SPEC:MIL-C-5015 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | MAX038EWP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Circular Connector; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:18; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:18-18; MIL SPEC:MIL-C-5015 RoHS Compliant: No |
| 中文描述： | SQUARE; TRIANGULAR; SINE; SAWTOOTH; PULSE, 20 MHz, WAVEFORM GENERATION, PDSO20 |
| 封裝： | SO-20 |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 203K |
| 代理商： | MAX038EWP |
M
High-Frequenc y Waveform Generator
16
______________________________________________________________________________________
Layout Considerations
Realizing the full performance of the MAX038 requires
careful attention to power-supply bypassing and board
layout. Use a low-impedance ground plane, and con-
nect all five GND pins directly to it. Bypass V+ and V-
directly to the ground plane with 1μF ceramic capaci-
tors or 1μF tantalum capacitors in parallel with 1nF
ceramics. Keep capacitor leads short (especially with
the 1nF ceramics) to minimize series inductance.
If SYNC is used, DV+ must be connected to V+, DGND
must be connected to the ground plane, and a second
1nF ceramic should be connected as close as possible
between DV+ and DGND (pins 16 and 15). It is not
necessary to use a separate supply or run separate
traces to DV+. If SYNC is disabled, leave DV+ open.
Do not open DGND.
Minimize the trace area around COSC (and the ground
plane area under COSC) to reduce parasitic capaci-
tance, and surround this trace with ground to prevent
coupling with other signals. Take similar precautions
with DADJ , FADJ , and IIN. Place C
F
so its connection
to the ground plane is close to pin 6 (GND).
__________Applic ations Information
Frequenc y S ynthesizer
Figure 6 shows a frequency synthesizer that produces
accurate and stable sine, square, or triangle waves with
a frequency range of 8kHz to 16.383MHz in 1kHz incre-
ments. A Motorola MC145151 provides the crystal-con-
trolled oscillator, the ÷N circuit, and a high-speed phase
detector. The manual switches set the output frequency;
opening any switch increases the output frequency.
Each switch controls both the ÷N output and an
MX7541 12-bit DAC, whose output is converted to a cur-
rent by using both halves of the MAX412 op amp. This
current goes to the MAX038 IIN pin, setting its coarse
frequency over a very wide range.
Fine frequency control (and phase lock) is achieved
from the MC145151 phase detector through the differ-
ential amplifier and lowpass filter, U5. The phase detec-
tor compares the ÷N output with the MAX038 SYNC
output and sends differential phase information to U5.
U5’s single-ended output is summed with an offset into
the FADJ input. (Using the DAC and the IIN pin for
coarse frequency control allows the FADJ pin to have
very fine control with reasonably fast response to switch
changes.)
A 50MHz, 50
lowpass filter in the output allows pas-
sage of 16MHz square waves and triangle waves with
reasonable fidelity, while stopping high-frequency noise
generated by the ÷N circuit.
V+
PDI
SYNC
AO
DADJ
PDO
FADJ
0.118"
(2.997mm)
0.106"
(2.692mm)
A1
COSC
GND
IIN
GND
GND
DGND
DV+
GND
GND
REF
V-
OUT
TRANSISTOR COUNT: 855
SUBSTRATE CONNECTED TO GND
___________________Chip Topography
相關PDF資料 |
PDF描述 |
|---|---|
| MAX100 | 250Msps, 8-Bit ADC with Track/Hold(250Msps,單通道，并行,8位模數轉換器) |
| MAX1031ACEG-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1031BCTI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1031BETI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX104 | 【5V, 1Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX038EWP+ | 制造商:Maxim Integrated Products 功能描述:HIGH FREQ WAVEFORM GENERATOR - Rail/Tube |
| MAX038EWP+T | 制造商:Maxim Integrated Products 功能描述:HIGH-FREQ WAVEFORM GENERATOR - Tape and Reel |
| MAX03G | 制造商:Aavid Thermalloy 功能描述:CLIP FOR TO 制造商:Aavid Thermalloy 功能描述:HEAT SINK CLIP - MAX TO220/218/247 制造商:Aavid Thermalloy 功能描述:Standard Force Clip 制造商:Aavid Thermalloy 功能描述:Thrml Mgmt Access Heat Sink Clip |
| MAX03G_INVALID | 制造商:Aavid Thermalloy 功能描述: |
| MAX03-H | 功能描述:散熱片 22.91N (5.15 LBS) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
發布緊急采購，3分鐘左右您將得到回復。