- 您現在的位置：買賣IC網 > PDF目錄359122 > M95256-BN5T (意法半導體) 256/128 Kbit Serial SPI Bus EEPROM With High Speed Clock PDF資料下載
參數資料
| 型號： | M95256-BN5T |
| 廠商： | 意法半導體 |
| 元件分類： | EEPROM |
| 英文描述： | 256/128 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| 中文描述： | 一百二十八分之二百五十六千位串行SPI總線的EEPROM高速時鐘 |
| 文件頁數： | 14/39頁 |
| 文件大?。?/td> | 580K |
| 代理商： | M95256-BN5T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
M95256, M95128
14/39
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction al-
lows the Status Register to be read. The Status
Register may be read at any time, even while a
Write or Write Status Register cycle is in progress.
When one of these cycles is in progress, it is rec-
ommended to check the Write In Progress (WIP)
bit before sending a new instruction to the device.
It is also possible to read the Status Register con-
tinuously, as shown in
Figure 10.
.
The status and control bits of the Status Register
are as follows:
WIP bit.
The Write In Progress (WIP) bit indicates
whether the memory is busy with a Write or Write
Status Register cycle. When set to 1, such a cycle
is in progress, when reset to 0 no such cycle is in
progress.
WEL bit.
The Write Enable Latch (WEL) bit indi-
cates the status of the internal Write Enable Latch.
When set to 1 the internal Write Enable Latch is
set, when set to 0 the internal Write Enable Latch
is reset and no Write or Write Status Register in-
struction is accepted.
BP1, BP0 bits.
The Block Protect (BP1, BP0) bits
are non-volatile. They define the size of the area to
be software protected against Write instructions.
These bits are written with the Write Status Regis-
ter (WRSR) instruction. When one or both of the
Block Protect (BP1, BP0) bits is set to 1, the rele-
vant memory area (as defined in
Table 3.
) be-
comes
protected
against
instructions. The Block Protect (BP1, BP0) bits
can be written provided that the Hardware Protect-
ed mode has not been set.
SRWD bit.
The Status Register Write Disable
(SRWD) bit is operated in conjunction with the
Write Protect (W) signal. The Status Register
Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware
Protected mode (when the Status Register Write
Disable (SRWD) bit is set to 1, and Write Protect
(W) is driven Low). In this mode, the non-volatile
bits of the Status Register (SRWD, BP1, BP0) be-
come read-only bits and the Write Status Register
(WRSR) instruction is no longer accepted for exe-
cution.
Write
(WRITE)
Figure 10. Read Status Register (RDSR) Sequence
C
D
S
2
1
3
4
5
6
7
8
9 10 11 12 13 14 15
Instruction
0
AI02031E
Q
7
6
5
4
3
2
1
0
Status Register Out
High Impedance
MSB
7
6
5
4
3
2
1
0
Status Register Out
MSB
7
相關PDF資料 |
PDF描述 |
|---|---|
| M95256-BN6 | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-BN6G | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-BN6P | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-MN5T | 256/128 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-MN6 | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M95256-BN6 | 功能描述:電可擦除可編程只讀存儲器 5.5V 256K (32Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95256-BN6G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-BN6P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-BN6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-BN6TG | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
發布緊急采購，3分鐘左右您將得到回復。