參數資料
型號: M93C06-MB6G
廠商: STMICROELECTRONICS
元件分類: PROM
英文描述: 16 X 16 MICROWIRE BUS SERIAL EEPROM, DSO8
封裝: 2 X 3 MM, LEAD FREE, MLP-8
文件頁數: 27/31頁
文件大?。?/td> 533K
代理商: M93C06-MB6G
5/31
M93C86, M93C76, M93C66, M93C56, M93C46, M93C06
cle, a Busy/Ready signal is available on Serial
Data Output (Q) when Chip Select Input (S) is driv-
en High.
An internal Power-on Data Protection mechanism
in the M93Cx6 inhibits the device when the supply
is too low.
Figure 3. DIP, SO, TSSOP and MLP
Connections (Top View)
Note: 1. See PACKAGE MECHANICAL section for package di-
mensions, and how to identify pin-1.
2. DU = Don’t Use.
Table 4. 90° Turned-SO Connections
Note: 1. See PACKAGE MECHANICAL section for package di-
mensions, and how to identify pin-1.
2. DU = Don’t Use.
The DU (Don’t Use) pin does not contribute to the
normal operation of the device. It is reserved for
use by STMicroelectronics during test sequences.
The pin may be left unconnected or may be con-
nected to VCC or VSS. Direct connection of DU to
VSS is recommended for the lowest stand-by pow-
er consumption.
MEMORY ORGANIZATION
The M93Cx6 memory is organized either as bytes
(x8) or as words (x16). If Organization Select
(ORG) is left unconnected (or connected to VCC)
the x16 organization is selected; when Organiza-
tion Select (ORG) is connected to Ground (VSS)
the x8 organization is selected. When the M93Cx6
is in stand-by mode, Organization Select (ORG)
should be set either to VSS or VCC for minimum
power consumption. Any voltage between VSS
and VCC applied to Organization Select (ORG)
may increase the stand-by current.
POWER-ON DATA PROTECTION
To prevent data corruption and inadvertent write
operations during power-up, a Power-On Reset
(POR) circuit resets all internal programming cir-
cuitry, and sets the device in the Write Disable
mode.
At Power-up and Power-down, the device
must not be selected (that is, Chip Select Input
(S) must be driven Low) until the supply
voltage reaches the operating value VCC
specified in Table 9. to Table 11..
When VCC reaches its valid level, the device is
properly reset (in the Write Disable mode) and
is ready to decode and execute incoming
instructions.
For the M93Cx6 devices (5V range) the POR
threshold voltage is around 3V. For the M93Cx6-
W (3V range) and M93Cx6-R (2V range) the POR
threshold voltage is around 1.5V.
VSS
Q
ORG
DU
C
SVCC
D
AI01929B
M93Cx6
1
2
3
4
8
7
6
5
1
VSS
Q
ORG
DU
C
S
VCC
D
AI00900B
M93Cx6
2
3
4
8
7
6
5
相關PDF資料
PDF描述
MT48LC4M16A2F4-6IT:G 4M X 16 SYNCHRONOUS DRAM, 5.5 ns, PBGA54
MT46V32M8FG-6TIT:G 32M X 8 DDR DRAM, 0.7 ns, PBGA60
MT46V32M8BG-6AT:G 32M X 8 DDR DRAM, 0.7 ns, PBGA60
M29F800FB55N3E2 512K X 16 FLASH 5V PROM, 55 ns, PDSO48
MC12L1NZGF ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.25A, 28VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
M93C06MN 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit, 1Kbit and 256bit 8-bit or 16-bit wide
M93C06-MN6 功能描述:電可擦除可編程只讀存儲器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M93C06-MN6T 功能描述:電可擦除可編程只讀存儲器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M93C06-WBN6 功能描述:電可擦除可編程只讀存儲器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M93C06-WMN6 功能描述:電可擦除可編程只讀存儲器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8