- 您現在的位置：買賣IC網 > PDF目錄370985 > M62002FP (Mitsubishi Electric Corporation) LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES PDF資料下載
參數資料
| 型號： | M62002FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| 中文描述： | 低功率2輸出系統復位IC系列 |
| 文件頁數： | 5/6頁 |
| 文件大小： | 74K |
| 代理商： | M62002FP |
( 5
ELECTRIC
MITSUBISHI
M62001L,FP/M62002L,FP/M62003L,FP/M62004L,FP/
M62005L,FP/M62006L,FP/M62007L,FP/M62008L,FP
LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES
MITSUBISHI<Dig.Ana.INTERFACE>
OPERATION PRINCIPLE
DESCRIPTION
In general,the memory backup function of
a microcomputer,as shown in figure,uses two diodes to switch
between main power supply and backup power supply.The
M62001~M62008 are ICs that,in such memory backup
operation,monitor in 2 steps each voltage on the V
DD
line.
V
DD
INT
RESET
INT
RESET
M62001
MAIN POWER
SUPPLY
BACKUP
POWER
SUPPLY
Vcc
MICROCOMPUTER
SYSTEM
The ICs have an intelligent sequence such as substantial
hysteresis action of RESET toward normal state at restoration of
supply voltage,as well as 2-step detection in low power
dissipation mode.
OPERATION IN DETAIL
1.Two Step Detection
The ICs perform 2-step detection of supply voltage and have 2
output pins (INT and RESET).Although they have 2 comparators
for 2-step detection,they differ significantly from such that are
simply provided with independent detectors,because the RESET
output signal is dependent at power-up and the like upon the
INT output signal.
2.INT output (Detection of 4.45V and 4.25V)
The INT output at the power-up of supply voltage detects V
SH
(4.45V/4.25V)to inform the microcomputer system of the fact
that the supply voltage has reached its normal level.When the
supply voltage drops from its normal level to
V
SL
(4.45V/4.25V)an interruption signal is output to alter the
microcomputer system into RAM backup mode. The
microcomputer at this point enters sleep state and secures
memory by a stop command issued by the interruption
signal.These detection voltage ,V
SH
the rise,and V
SL
the fall,of
supply voltage,have a 100-mV hysteresis voltage between
themselves.
V
SH
-V
SL
=100(mV)
..
INT OUTPUT VOLTAGE VS.
SUPPLY VOLTAGE
SUPPLY VOLTAGE Vcc(V)
0
1
2
3
4
5
4.0
4.2
4.4
4.6
4.8
5.0
VSL
VSH
3.RESET Output (Detection of 2.15V)
The RESET outputs a signal to prevent the microcomputer from
malfunctioning due to a drop in supply voltage.
When powering up,RESET is kept at low level until the supply
voltage reaches V
SH
.If the supply voltage rises to V
SH
,RESET
is set to high level.By inserting a capacitor between the Cd pin
and GND,it is possible to produce a desired delay time (td).To
set a delay time,equation below is used.
t..
Once the supply voltage has exceeded V
SH
and the RESET
output is set to high level,RESET maintains the high level until
the supply voltage drops to V
BATT
.When the supply voltage
drops to V
BATT
,RESET goes low thereby resetting and
initializing the microcomputer.
The RESET output has a large hysteresis voltage of
approximately 2V between the rise in supply voltage at power-
up and its fall.
5
0
1
2
3
4
5
2
3
4
5
VSH
VBATT
SUPPLY VOLTAGE Vcc
RESET OUTPUT VOLTAGE VS.
SUPPLY VOLTAGE
相關PDF資料 |
PDF描述 |
|---|---|
| M62002L | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| M62003FP | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| M62003L | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| M62004FP | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| M62004L | LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M62002FP(#TF0J) | 制造商:Renesas Electronics Corporation 功能描述: |
| M62002L | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low Power 2 Output System Reset IC Series |
| M62003FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:LOW POWER 2 OUTPUT SYSTEM RESET IC SERIES |
| M62003L | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low Power 2 Output System Reset IC Series |
| M62003P | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low Power 2 Output System Reset IC Series |
發布緊急采購，3分鐘左右您將得到回復。