參數資料
型號： M50FW080N5P
廠商： 意法半導體
英文描述： 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
中文描述： 8兆1兆× 8，統一座3V電源閃存固件集線器
文件頁數： 12/56頁
文件大小： 292K
代理商： M50FW080N5P
Signal descriptions
M50FW080
12/55
2
Signal descriptions
There are two distinct bus interfaces available on this device. The active interface is selected
before power-up, or during Reset, using the Interface Configuration Pin, IC.
The signals for each interface are discussed in the
Firmware Hub (FWH) signal descriptions
section and the
Address/Address Multiplexed (A/A Mux) signal descriptions
section,
respectively, while the supply signals are discussed in the
Supply signal descriptions
section.
2.1
Firmware Hub (FWH) signal descriptions
For the Firmware Hub (FWH) Interface see
Figure 1
and
Table 1
.
2.1.1
Input/Output communications (FWH0-FWH3)
All Input and Output Communication with the memory take place on these pins. Addresses
and Data for Bus Read and Bus Write operations are encoded on these pins.
2.1.2
Input communication frame (FWH4)
The Input Communication Frame (FWH4) signals the start of a bus operation. When Input
Communication Frame is Low, V
IL
, on the rising edge of the Clock a new bus operation is
initiated. If Input Communication Frame is Low, V
IL
, during a bus operation then the
operation is aborted. When Input Communication Frame is High, V
IH
, the current bus
operation is proceeding or the bus is idle.
2.1.3
Identification inputs (ID0-ID3)
The Identification Inputs select the address that the memory responds to. Up to 16
memories can be addressed on a bus. For an address bit to be ‘0’ the pin can be left floating
or driven Low, V
IL
; an internal pull-down resistor is included with a value of R
IL
. For an
address bit to be ‘1’ the pin must be driven High, V
IH
; there will be a leakage current of I
LI2
through each pin when pulled to V
IH
; see
Table 20
.
By convention the boot memory must have address ‘0000’ and all additional memories take
sequential addresses starting from ‘0001’.
2.1.4
General-purpose inputs (FGPI0-FGPI4)
The General Purpose Inputs can be used as digital inputs for the CPU to read. The General
Purpose Input Register holds the values on these pins. The pins must have stable data from
before the start of the cycle that reads the General Purpose Input Register until after the
cycle is complete. These pins must not be left to float, they should be driven Low, V
IL,
or
High, V
IH
.
相關PDF資料
PDF描述
M50FW080N5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5P 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50LPW002 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory
M50LPW002K 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50FW080N5T 制造商:Micron Technology Inc 功能描述:
M50FW080N5TG 功能描述:閃存 8 Mbit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FW080N5TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB1G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*