- 您現在的位置：買賣IC網 > PDF目錄377829 > M50FLW040BNB5P (意法半導體) 4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory PDF資料下載
參數資料
| 型號： | M50FLW040BNB5P |
| 廠商： | 意法半導體 |
| 英文描述： | 4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| 中文描述： | 4兆位（5 × 64KB之座3 × 16 × 4KB的部門）3V電源固件集線器/低引腳數快閃記憶體 |
| 文件頁數： | 45/52頁 |
| 文件大?。?/td> | 417K |
| 代理商： | M50FLW040BNB5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
45/52
M50FLW040A, M50FLW040B
Figure 23. Double/Quadruple Byte Program Flowchart and Pseudo code (FWH Mode Only)
Note: 1. A Status check of SR3 (V
PP
Invalid) and SR4 (Program Error) can be made after each program operation by following the correct
command sequence.
2. If an error is found, the Status Register must be cleared before further Program/Erase operations.
3. A0 and/or A1 are treated as Don
’
t Care (A0 for Double Byte Program and A1-A0 for Quadruple Byte Program).
For Double Byte Program: Starting at the Start Address, the first data Byte is programmed at the even address, and the second at
the odd address.
For Quadruple Byte Program: Starting at the Start Address, the first data Byte is programmed at the address that has A1-A0 at 00,
the second at the address that has A1-A0 at 01, the third at the address that has A1-A0 at 10, and the fourth at the address that
has A1-A0 at 11.
AI08423B
Read Status
Register
YES
NO
SR7 = 1
YES
NO
SR3 = 0
NO
SR4 = 0
VPP Invalid
Error (1, 2)
Program
Error (1, 2)
Double/Quadruple Byte Program command:
–
write 40h or 10h
–
write Start Address and 2/4 Data Bytes
(3)
(memory enters read status state after
the Double/Quadruple Byte Program command)
do:
–
Read Status Register
–
If SR7=0 and a Program/Erase Suspend
command has been executed
–
SR7 is set to 1
–
Enter suspend program loop
If SR3 = 1, VPP invalid error:
–
error handler
If SR4 = 1, Program error:
–
error handler
Suspend
Suspend
Loop
NO
YES
Write 40h or 10h
Start
Write Start Address
and 2/4 Data Bytes
(3)
YES
End
YES
NO
SR1 = 0
Program to Protected
Block Error (1, 2)
If SR1 = 1,
Program to protected block error:
–
error handler
相關PDF資料 |
PDF描述 |
|---|---|
| M50FLW040BNB5T | 4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW040BNB5TG | 4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW040BNB5TP | 4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW040A | 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory |
| M50FLW040A_06 | 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FLW040BNB5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW040BNB5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FLW040BNB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW080 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW080A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。