參數資料
型號: M50FLW040AK5G
廠商: 意法半導體
英文描述: 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
中文描述: 4兆位(5】64字節塊3】16】4 Kbyte的)3 - V電源供電固件集線器/低引腳數的閃存
文件頁數: 34/64頁
文件大?。?/td> 338K
代理商: M50FLW040AK5G
Status Register
M50FLW040A, M50FLW040B
34/64
5.3.4
Block Protection status (Bit SR1)
The Block Protection Status bit can be used to identify if the Program or Erase operation has
tried to modify the contents of a protected block. When the Block Protection Status bit is to
‘0’, no Program or Erase operations have been attempted to protected blocks since the last
Clear Status Register command or hardware reset. When the Block Protection Status bit is
‘1’, a Program or Erase operation has been attempted on a protected block.
Once it is set to ‘1’, the Block Protection Status bit can only be reset to ‘0’ by a Clear Status
Register command or by a hardware reset. If it is set to ‘1’, it should be reset before a new
Program or Erase command is issued, otherwise the new command will appear to have
failed, too.
Using the A/A Mux Interface, the Block Protection Status bit is always ‘0’.
5.3.5
Reserved (Bit SR0)
Bit 0 of the Status Register is reserved. Its value should be masked.
Table 14.
Status Register bits
Operation
SR7
SR6
SR5
SR4
SR3
SR2
SR1
Program active
‘0’
X
(1)
1.
For Program operations during Erase Suspend Bit SR6 is ‘1’, otherwise Bit SR6 is ‘0’.
‘0’
‘0’
‘0’
‘0’
‘0’
Program suspended
‘1
X
(1)
‘0’
‘0’
‘0’
‘1’
‘0’
Program completed successfully
‘1’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘0’
Program failure due to V
PP
Error
‘1’
X
(1)
‘0’
‘1’
‘1’
‘0’
‘0’
Program failure due to Block Protection (FWH/LPC
Interface only)
‘1’
X
(1)
‘0’
‘1’
‘0’
‘0’
‘1’
Program failure due to cell failure
‘1’
X
(1)
)
‘0’
‘1’
‘0’
‘0’
‘0’
Erase active
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase suspended
‘1’
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase completed successfully
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase failure due to V
PP
Error
‘1’
‘0’
‘1’
‘0’
‘1’
‘0’
‘0’
Erase failure due to Block Protection (FWH/LPC
Interface only)
‘1’
‘0’
‘1’
‘0’
‘0’
‘0’
‘1’
Erase failure due to failed cell(s) in block
‘1’
‘0’
‘1’
‘0’
‘0’
‘0’
‘0’
相關PDF資料
PDF描述
M50FLW040AK5P 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5TG 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5TP 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AN5G 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW080BK5P 8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50FLW040AK5P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
M50FLW040AK5TG 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FLW040AK5TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AN1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory